Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

bowl lathe design questions

Posts

bowl lathe design questions

#1

bowl lathe design questions

chris rolke

>i am thinking of making a bowl lathe ( for roughly 24 " diameter bowls)

i have a few questions

first off i like this one with a few exceptions

http://www.taunton.com/finewoodworking/SkillsAndTechniques/SkillsAndTechniquesArticle.aspx?id=26160

i dont care for the 1" spindle would rather go for a 1.25" spindle

i am thinking of using pillow blocks and a machined shaft to get my spindle

how would the shaft stay in the pillow blocks?

i also dont care for the rpm range (low end is too fast )thinking of going to a VFD or the like

anything anyone has for idea about making a lathe and or design ideas

thnaks

Re: bowl lathe design questions

#2

Re: bowl lathe design questions

Al Crandall (N.E. of Indy)

>"how would the shaft stay in the pillow blocks? "

The last pillow blocks I bought had a shoulder on the bearing sleeve which extended outside the block. This shoulder had a set screw installed which would drive tight against the shaft. You might also think about split shaft clamps to trap ball bearing thrust washers.

Re: bowl lathe design questions

#3

Re: bowl lathe design questions

chris rolke

>thanks

havent thought of that

i am wanting to do this on the Cheap side but have a durable lathe as well

Re: bowl lathe design questions

#4

Re: bowl lathe design questions *LINK*

Derek Andrews

>Looking at the items turned on his lathe, they seem to be possibly rather light weight compared to a big block of green wood, so I think you are on the right track to beef up the design. I agree with your thinking on the larger diameter headstock spindle. Bigger the better in my opinion as long as you can get chucks and faceplates to fit.

Electronic variable speed is another must too, assuming it is within budget, but do consider the pro's and con's of the various systems now available.

The bed looks a bit long to me. I like to be able to stand right up close to the toolrest, and think this design may get in the way. You might want to try something like the arrangement on the VB36 and dispense with the bed altogether.

An easy to adjust toolrest is also a big bonus. Having to mess with spanners to adjust it may become a bit tiresome.

Good luck whatever you do.


The ToolRest - a blog for woodturners

Re: bowl lathe design questions

#5

Re: bowl lathe design questions

Bruce in Saint John,N.B.

>Myself I would prefer a press fit between the shaft and the bearing in the pillow block. A 1" or 1 1/4" shaft could use a .002-.003 press fit. When you have the shaft fabricated at the machine shop, take the pillow block with you so the machinest is able to measure the bearing in the pillow block so he in turn will be able to machine the shaft to the proper size. Even if you gave him the number off the bearing as he will have a chart that will give him the dimensions of the particular bearing. Good luck and be sure and post a pix of the lathe.

Re: bowl lathe design questions

#6

Re: bowl lathe design questions

Doug Thompson near Cleveland

>Start with a shaft diameter larger than what you need. Keep this large diameter the lenght BETWEEN the pillow blocks. Spend a few extra bucks and over size the bearings.

Let us know.

Re: bowl lathe design questions

#7

Denis Putland

Re: bowl lathe design questions

Denis Putland

>Hi

You could build a head stock as you want with pillow block bearings with set screw locking collars and perhaps have a lathe that you will be happy with.

But the mounting method of a pillow block bearing is not ideal for end thrust or the effects created by an out of balance piece of wood.

For the most vibration free head stock I would suggest flange mounted bearings with the shaft machined as suggested for a press fit and use the locking screws only to control the thrust effects.

If you get a high quality ball bearings there is no need to worry about the thrust causing any problems with your bearings.

Buy your bearing from a shop that sells bearings for a living and not from a box store.

There are many levels of quality for that 1 1/2 inch bearing you want and the bearing shop will be able to guide you to the right one.

My 3 1/2 cents worth.

Denis

Re: bowl lathe design questions

#8

Re: bowl lathe design questions

chris rolke

>i am still in them mental design side of this so this is helping me out quite a bit

i really want to go large but right now cant afford a bowl lathe but building one i can possibly sneak past the wife :)

Re: bowl lathe design questions

#9

Bob Moffett

Re: bowl lathe design questions

Bob Moffett

>Look a couple of days back, or maybe a week, for a posting by Earl Kennedy. He make a lathe simular to what you may be thinking about. He would be a good source for advise.

Re: bowl lathe design questions

#10

Re: bowl lathe design questions

Barry Irby

>I started to make a big lathe once, several years ago. I took a shaft I found to a machinist and then lost interest. If I can find it, I would give it to you.

Also, I believe I have a shaft a friend gave me. If I am not mistaken, it a two inch shaft that may be 20� or two feet long. There are two high quality pillow blocks with it if I can find it. This is just a straight piece of shaft. No machining done on it yet. If you are interested, its yours for the shipping, but that might be pretty rank, considering what it weighs.

Re: bowl lathe design questions

#11

Re: bowl lathe design questions

Jimiles-Charlotte, NC

>Fine Woodworking March/April 1986 has 3 lathe designs, one sounds like what you describe if you can access it.

Re: bowl lathe design questions

#12

Re: bowl lathe design questions

chris rolke

>yea please i am extremely interested in what you have

please let me know

thanks