Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Replacement blade shank size

Posts

Replacement blade shank size

#1

Replacement blade shank size

Doug Thompson near Cleveland

>I need your thoughts and ideas;

Tool steel is sold .015 (1/64) oversize and as is will fit all aftermarket handles except a 3/8 in a Oneway because it's the same size, this shank size needs to be turned down a bit.

To make your own wood handle would require a drill bit 1/64 larger than a commom size. Example; 1/2 - 33/64, 5/8 - 41/64

Should a 1/2 - 5/8 tool shank be turned down or not?

What are your thoughts or am I worried about fifteen thousands for nothing.

Re: Replacement blade shank size

#2

Re: Replacement blade shank size

Bob Fawcett

>Most people have drills up to 1/2" in regular twist drills. most don't have a 33/64" bit in anything. Is the extra machining operation worth the cost of a drill bit?

Re: Replacement blade shank size

#3

Re: Replacement blade shank size

Ronnie

>If you are making a wooden handle ,drill it as close as you can , run the bit in a couple of times , put the ferrule on and drive it in for a tight fit.I've make several with no problems.

Ronnie

Re: Replacement blade shank size

#4

Offer both sizes

Ray Thompson - Middletown,IN

>Make your standard tool the one with the oversize steel and offer a turned down shank for the extra cost of machining. Satisfies everyone, except the guy who has to handle all the different products. But then he is a bright guy and can handle anything. ;-)

Ray

Re: Replacement blade shank size

#5

Re: Most wood bits have enough...

Jamie Donaldson

>... wobble to compensate for those tolerances.I certainly wouldn't want to spend extra money to have a larger shaft machined to a smaller size.

Re: Replacement blade shank size

#6

Jamie, the tools you have are not ground problems?

Doug Thompson near Cleveland

>this is the standard stock size. What handle did you use or did you make your own?

Re: Replacement blade shank size

#7

I don't think

Ray Thompson - Middletown,IN

>.016 slop in a drilled hole would be a common occurance. Having that much would indicate a problem somewhere. A few thousandths over I could see but not that much.

Ray

Re: Replacement blade shank size

#8

Re: Replacement blade shank size

john lucas

>Doug Most woodturners don't want to mess with trying to buy odd size drills or drilling too big a hole and then filling with epoxy. Personally I would just drill it half inch and then heat the end and drive it in the handle but I would dare say no more than one or two in the two clubs I go to would try that.

I think I would turn them down to common sizes unless the cost gets prohibitive. For one thing If I were to make an aftermarket handle to sell I would probably make it a common size such as 1/2, 5/8, or 3/4.

Re: Replacement blade shank size

#9

What's the old trick Ray...

Doug Thompson near Cleveland

>Sharpen the bit so the point is off center... that's good for a few. LoL

Re: Replacement blade shank size

#10

Re: Doug- they mounted right into ...

Jamie Donaldson

>... 2 old Sorby handles without any redrilling. I prefer wooden handles over metal, and I can see that the metal handles would create more of a fit problem.

Re: Replacement blade shank size

#11

Re: Doug- they mounted right into ...

Doug Thompson near Cleveland

>Thank you Jamie... interesting.

Re: Replacement blade shank size

#12

You decided and here's what will happen

Doug Thompson near Cleveland

>The shank WILL be turned down to a commom fractional size. This is a extra step that I couldn't decide what to do. I will keep a few aside to fit a old Glaser handle.

THANK YOU!!!

Re: Replacement blade shank size

#13

Yep, grind one flute longer than the other

Ray Thompson - Middletown,IN

>and you can drill oversize, not a lot but oversize. A properly sharpened drill will drill to size, it may not be straight, but that's a subject for another thread. Dad always said he could grind a drill to drill undersized, but I never figured out if he could or just pulling my chain.

Ray

Re: Replacement blade shank size

#14

Re: What's the old trick Ray...

john lucas

>sharpening off center will work but if everything is not clamped in place it will drill an oval hole.

Re: Replacement blade shank size

#15

Re: You decided and here's what will happen

Jerry from Lapel In.

>I want mine turned down with a deeper flute.

Re: Replacement blade shank size

#16

Yeah, it will be oval, big, ragged

Ray Thompson - Middletown,IN

>and just plain ugly, and if you get to carried away the drill may break.

Ray

Re: Replacement blade shank size

#17

Yeah, it will be oval, big, ragged

Ray Thompson - Middletown,IN

>and just plain ugly, and if you get to carried away the drill may break. If you need an oversize hole there are far better solutions.

Ray

Re: Replacement blade shank size

#18

Re: You decided and here's what will happen

Doug Thompson near Cleveland

>Jerry,

You got .020 of that back. While I think of it the Ohio valley woodturners are having a symposium in October don't plan the Indyfest the same weekend. I would like to attend both.

Who said turn the shanks down... I just finished!