Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

ca glue fumes

Posts

ca glue fumes

#1

ca glue fumes

jared

>I have been working with doing stone inlays in some of my turnings. I have been using starbond CA, thin variety. I had been using my Milwaukee sander to take the inlay and built up glue down to level of the wood. I got a bright idea a couple of days ago to use my hand held 4 inch makita grinder, that is mostly used to grind down welds on metal, with an abrasive disk to sort of rough grind the stone and built up CA to almost level with the wood. It works like a charm, is much faster and with a light touch you can avoid marking up the wood. I then used my regular sanding routine to finish grinding off the stone and glue and for final finish and polishing. The problem is that when I use the grinder, there seems to be an almost choking amount of fumes of some sort that are released during grinding. It really bothers my eyes and I can feel it in my throat. I use a shop wide dust collector with a cone as close as I can to the point of grinding and wear safety glasses and a 3m dust mask. Is it increased heat from the grinding that releases the fumes? Is it a smaller particle size that is released? If I got the odorless CA {at twice the cost} would that take care of the problem? Anybody have any experience with anything like this? Thanks in advance Jared

Re: ca glue fumes

#2

Re: ca glue fumes

eaglesc

>Just a SWAG but I am guessing it is the heat.

I use a lot of CA on the lathe and the D.C. grabs the fumes.

When doing glue ups or for tubes I have noticed a minute odor but evidently it doesn't bother me as much as others.

One thing I have noticed is the smell isn't as strong when the CA has had a long enough time to set.

Re: ca glue fumes

#3

JL

Re: ca glue fumes

JL

>Uncured cyanoacrylate can give off a variety of "fumes". Methyl-2-Cyanoacrylate often causes irritation to the eyes and respiratory tract as do some of the other varieties (ethyl cyanoacrylate, etc.). That's usually the uncured stuff though. If it is fully polmerized it shouldn't give off many fumes. Are you using the CA accelerator?

I don't know about the heating byproducts. If you are grinding at high speed, you may be generating various nitrogen oxides and a variety of carbon compounds. Some of these are irritating also. You say that you don't notice it when sanding.

It could be that the initial grinding exposes "pockets" of uncured CA, which then get into the air. These pockets then cure out so that they are fully cured by the time you sand. A quick "test" is to try a little of the CA accelerator in your routine. If you don't notice the fumes when you use it, that may be the answer.

Another thought - is it time dependant? If you were to let it cure overnight, do you still get the irritation?

Just some random thoughts.

Re: ca glue fumes

#4

Re: ca glue fumes

Wally Dickerman in Arizona

>I have used quite a lot of turquoise in my turnings. I use 3 sizes of turquoise granules and mix it with epoxy to form a paste which I apply to the void with an artist's spatula. After overnight drying, I use my right-angle drill and sanding discs to bring the mix down to the level of the wood. There are no fumes from the expoxy.

A suggestion...buy some glitter from a craft store and add a little to the mix. I use blue for turquoise. Adds a little sparkle to the stone.

Wally

Re: ca glue fumes

#5

Re: ca glue fumes

jared

>Some good points. The CA had been curing for 16 hours at least. I had used a little accelerator on it but not a great deal. I went back out in the shop and did a little more experimenting. I used the sander some more and while there is a little smell it wasnt that bad. THe thing that I did notice was that the dust coming off with the sander was a much larger particle size than the grinder created. The dust from the grinder was nearly invisible but the dust from the sander was just that, it looked like fine sanding dust off wood or any thing else. I think that is the key to this whole thing. Jared

Re: ca glue fumes

#6

Re: ca glue fumes

John Kyler

>The dust or fumes from CA is not good for you at all. People will build a level where they develop asthma from CA.

And if there is stone mixed in silicosis is also very bad.

I turn with a Trend power visor and avoid CA as much as possible.

And the hood wont stop the CA fumes...

John

Re: ca glue fumes

#7

Right - All Dangerous stuff!

Bill Howatt

>