Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

A milestone piece

Posts

A milestone piece

#1

A milestone piece

David Breth

>I held this piece of wood in reserve for a long time, and finally decided to have at it. It is a crotch piece of I have absolutely no idea what that I got from a tree that was taken down for a convenience store.

The reason it is a milestone piece for me is that this was the last piece of wood that I ever cut into blank form using a bow saw. When I first started, that's how I did it. Awful, almost tearful experience, fraught with frustration. I would end up in my basement, with a log segment wedged into my vice, and cut it lengthwise with the bowsaw. Since the wood, green wood especially, would close in on itself as I cut, I was forever bamming more wedges into the cut so I could keep moving the saw blade. I probably had a good hour plus in cutting this one piece out, and I botched the cut somewhat, ending up with a rectangular blank. I must have done ten bowls like that before I finally broke down and got a chainsaw.

So, this blank survived air drying, and became this little bitty plate, maybe 7 inches diameter. Probably about an eigth of an inch thick. Hold it to the light and you get a pretty cool pattern glowing through. Nice feathering (I think that's what the pattern is called). Finish is Minwax Antique Oil. There are lots of coats, because whenever it was too late at night to start turning, but I felt like being productive, I'd put another coat on. There must be eight or ten coats, applied pretty much because of wanting to do SOMETHING on any particular night. Picture doesn't show it, but if you hold it right, you can see there are some little scratch marks in there from steel wool I used to knock down some raised grain after the first coat of oil. #@@$#(*^*%$ is what I say to that. I've rarely if ever had success using steel wool for that.

Sometimes I surprise myself with the ability I showed early on to pick a nice piece of wood - I remember when I grabbed this one knowing that I could see the pattern within.

Anyway, thanks for looking. Interested to know what "milestones" you have had that meant a little something to you.

David B.


img

Re: A milestone piece

#2

Re: A milestone piece

tm

>Thats a stunning piece. Your experience with a bowsaw and wedges is

very similar to my own. I was trying to get a blank out of a venerable sycamore from my own front yard. I didn't want to

use a chainsaw because I didn't want to spend the money it takes to buy a good one. Damn near wrecked myself sawing and pounding wedges.

I was so sore I couldn't pick up a gouge for a week. The end result

isn't nearly as nice as yours.

A few hundred dollars spent on a good saw amounts to more time spent

at the toolrest, which after learning the hard way is where I would

rather be.

tm

Re: A milestone piece

#3

Re: A milestone piece

john lucas

>Georgeous piece. Well done. I remember my early experiences gathering wood. I didn't have a chainsaw and we had to heat the house with a cheap woodstove. I would find downed wood on our property and hook a rope to it. I had a backpack frame that I hooked the rope to and would drag it out of the woods. My property was straight up and down, not flat so this was quite a chore.

Then I would saw it up with a bow saw. This carried over when I got my lathe. I would bow saw it to size and use a hatchet to knock off odd corners that stuck out. I didn't have a good vice so I used a piece of rope thrown over the blank and then stood on the rope to apply enough pressure. Talk about frustrating.

Re: A milestone piece

#4

Steve Kubien

In the same old boat

Steve Kubien

>I do not own a chainsaw...yet. A big bowsaw has lead me through some nasty stuff and will continue to do so for a few more months. You may remember the large burl I found a few weeks back? Yup, I going through it with a bowsaw. Some people believe this sort of thing builds character. For me, it just increases my reliance on vitamin I (ibuprofen).

That's a really nice looking piece. Personally, I prefer that sort of figured grain to just about anything else. Well done.

Steve Kubien

P.S. The circ saw was not used to cut the burl. It is just there for perspective.


img

Re: A milestone piece

#5

do you still have your coonskin hat?

robert davis

>

Re: A milestone piece

#6

Try a tool rental store..

Stuart Johnson

>

Re: A milestone piece

#7

Re: In the same old boat

John Lucas

>Steve I look at it as a good aerobic workout. It helps if you sing I've been working on a railroad while you do it.

Re: A milestone piece

#8

Re: In the same old boat

David Breth

>I always looked at it as though there was something more pure about prepping the blank with a bow saw. My hands had done the work every step of the way, and by the time a piece came off the lathe, I took a different sort of pride in it, more emotional in a sense. "Yer darn rite i made it!"

But now I'm smarter. Chainsaw. Bandsaw.