Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Help on tool

Posts

Help on tool

#1

Help on tool

Bill Hale / The Wood Spinner

>I am doing a 32" lazy susan for a Daughter in Law and am having trouble cutting the wedge shaped pieces to a perfect angle. I am using a table saw and a jointer.

My question is is how others do it ?

I am using 8/4 8" alder.

Thanks Bill in Casa Grande

Re: Help on tool

#2

Re: Help on tool

Carol from AZ

>I am assuming you are cutting the wedge angle on the table saw with a miter bar or a miter sled.

The problem almost always is getting the angle setting EXACTLY for the cut. Any little amount you are off is accumlative for each cut. Example, an octagon has 16 cuts. A half of a degree off is 16 times 1/2 a degree or 8 degrees when all the cuts are made.

My solution is to set the angle using an adjustable drafting triangle. Easily accurate to less than 1/2 degree and inexpensive at less than $20 bucks from Staples or Office Depot for the 6" model.

I've done lots of octagonal work. At the worst, I've had to fiddle the last mating with a block plane. I check at the quarter mating, and again at the 1/2 mating (with a straight edge).

Also to see how you are going to do, make 4 cuts on scrap so you have two pieces to mate. Mate them together and check with a dead-on square. They should dead square at the pointy end (what will be the center of your lazy susan).

Remember, errors are accumlative. Again, I use drafting triangles for these kinds of things. They're cheap and deadly accurate,and when you drop them they don't go out of square. I keep a set of 6", 8" and 12" of 45-90-45 good quality drafting triangles to use for machine set-up. Plus the adjustable drafting triangle.

Re: Help on tool

#3

Keith Tompkins

Re: Help on tool

keith tompkins

>Bill, this may be an easy way to do it. Make a sled for your table saw; run it through the blade...the saw cut becomes the reference point. Then, draw a circle divided by the sawcut. Divide the circle into as many segments as you require, this requires only the use of a compass, then attach a fence along the line of your choice.Make a test cut,making enough segments to complete a circle. (you may be happy with just a semi-circle) adjust the fence as necessary until you're happy, then secure the fence. I clamp segments into place to prevent movement.

If you glue the assembly together, and aren't happy with the fit, no problem.....using the sawcut in your sled as a reference, cut your assembly in half. Reglue it, allow to dry. rotate the assembly, and perform the same operation as many times as required. The result will be an absolutely perfect fit.

Re: Help on tool

#4

Re: Help on tool

eaglesc

>Keith THAT is brilliant!

Re: Help on tool

#5

Re: Help on tool

Bill Hale / The Wood Spinner

>Keith

I think I am a little dense tonight but is there anyway you could take a pic of what you meen. I am confused about the sled and angles of the cuts you can get from it.

Bill in Casa Grande

Re: Help on tool

#6

Keith Tompkins

Re: Help on tool

keith tompkins

>Bill, this should help. The yellow area represents the sled, I usually use plywood or mdf. The dotted line marked with a "C" represents the saw cut. The grey circle drawn inside the sled is divided into eight parts, but could be as many as you like...I use a compass for this; bisecting line C, then dividing each quadrant. The red area represents a fence; the angles drawn are used as the guide. "A" is the segment that is being cut. Commercially available holddown are available to secure the segment being cut, but I usually use homemade clamps. (Don't cut without securing the workpiece)

Last step, if necessary. Remove the fence (red), and place the glued-up assembly right where the grey circle is drawn. Secure the piece, aligning the segments with the sawcut in the sled,and make a cut; it will be a perfectly straight line through the piece. Glue back together, remount the assembly in the sled, rotate to a new line, and cut. Repeat as needed. Using a bit of care, it's possible to make a perfect segmented assembly with absolutely no gaps.

I've used variations of this sled for many years.


img

Re: Help on tool

#7

Keith Tompkins

Re: Help on tool

keith tompkins

>Thanks, eaglesc I don't do all that much segmented work any more, but this is one of the ways I cut perfect segmented rings (and staves)...no gaps, even with a thousand segments. The pic I included shows the accuracy that is possible. (the piece shown required 450 compound miter cuts, all done on a home-built saw sled.)


img

Re: Help on tool

#8

Re: Help on tool

John Bussom

>Bill, I wouldn't say you are dense, it hard to put it into prespective when looking at words and trying to visualize! Kieth's illustration and wording look great and I love that piece he showed a partial picture of.

Somewhere I have the instructions when I built my sleds and will attempt to find them for you today ASAP. I nothing else I will take a pic of mine and send you!

John

Re: Help on tool

#9

Re: Help on tool

John Bussom

>Bill,

Here are a couple of links for you to explore!

http://www.verifiedsoftware.com/goodturns/acumiter.htm

http://www.woodturner.org/products/aw/more_info/2005_winter_sled.pdf

http://www.turnedwood.com/framesled.html

Mine may look kind of shabby especially with my poor photo skils but a pic of mine, the bar on the right allows me to quickset the desired length of segment, another feature I added is a hold down right next to the cut.

One thing to add, the width of your board must be accurate because after you make the 1st cut the board is flipped (rear edge goes to the blade) to make your segmented piece.

I rarely need to do any sanding when I do my glueing, I dry fit then use large adjustable auto/hose clamps (dunno whatcha callem) and tightbond glue all at once.


img

Re: Help on tool

#10

Re: Help on tool

Bill Hale / The Wood Spinner

>Thank you all so much.

Daily, as I read postings on this site I am just blown away by the effort turners put into helping others.

I am realy proud to be a part of this site.

Good turning and be safe

Bill in Casa Grande, AZ.