Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Earls home made lathe

Posts

Earls home made lathe

#1

Earls home made lathe

Earl Kennedy

>I made this lathe for the same reason I turn bowls.I just like to make stuff.Didn't need it and it sure will not compare to my 3520 PM.I have not turned any thing on it yet.It is ready but still sitting on the pieces of pipe that I move it around on.May try it out tonight.It has a whopping 30inch swing but only 1 1/2 hp motor.A turning blank that is 12" and out of balance will probably make it walk all over the place.With the jack shaft I have all kinds of spidle speeds.From real slow to wow.It is just over 50" long.I used 3x3 box tubing for most of it.I fixed the tool rest so it locks down with just a twist of the leaver.The tail stock will lock with a wrench.May modify it so it is a lever operation later if I like the lathe enough.It is a east thing to do.Hope to fix it so I can stick wheels on it so it is easy to move and use as a demo lathe.I used all new pillow block bearing and put new bearings in the motor and it runs really quite.Also I can use all my tool rest that fit my PM.All the alignment of the bed,head and tail stock came out a lot better than I had hope for.I built the bed first and then every thing else was built to it.Really as good as some of the factory made lathes.I was just lucky on this.It was a fun project.I worked about a month on it.Any questions or comments are welcome.Yes I know the pictures are not great but if you look you can still see the lathe.


img

Re: Earls home made lathe

#2

Re: Earls home made lathe

David Walser

>Wow! Some more details, please: How much does it weigh. What did the materials cost? How did you align the head stock and the tail stock? Etc.

Re: Earls home made lathe

#3

WOW Earl

Bob Fawcett

>Looks great to me.

I would love to make something like that. I don't think I have the tools and skills to do so.

Tell me what tools it took. I have a welding machine, but no machine tools.

On the wheels, how about castors mounted on square tubing that fits just inside your leg cross pieces. Lift it a little and slide in the wheels. Add a pin to lock them during transport.

Looks like sand bags on the bottom frame could help with stability and weight.

I admire your creativity.

Re: Earls home made lathe

#4

Re: Earls home made lathe

john lucas

>Good job. I've always wanted to build a lathe for the same reason you did. Just because it's there. I know I probably can't build one better than my Powermatic but you never really know.

Re: Earls home made lathe

#5

Re: Earls home made lathe

Terry Quiram, Roanoke Illinois

>Earl, thats pretty neat. Looks to be extremely well made. You should probably shield those belts or some dope will get caught.

Terry

Re: Earls home made lathe

#6

Re: Earls home made lathe

Earl Kennedy

>David I cut 3 pieces of partacle board.Then I matched drilled a hole 15" up from the bottom in all 3 pieces.The hole was the size of the shaft.I bought 2 1/2' of shaft.I clamped the boards to the bed and with the shaft in the holes I hung the bearings on the shaft.I then bolted the uprights to the bearings and tacked welded the uprights on to the bed.This lined them up with the bed.This took some time because I wanted it as true as I could make it.The tail stock is just bolted to a steel box that was the right height.I centered the tail stock on the box by sliding it up to the spindle with 2 centers.Then just bolted it together.I had the spindle and the tail stock and the motor so I didn't have but a little bit of machine shop work done.I don't know how much it weighs.I probably have about 350.00 in the lathe.Had to buy 2 new bearings because 2 I had were no good.That was a extra 88.00.Bob I only used a welder,drill press,a 4" grinder,Hand drill,and odds and ends.Nothing fancy.Terry I plan on adding a belt guard but want to play with it some first.Hope this made some sence.Oh I used my table saw for a welding table to make the bed because it was the only really flat surface I had.Have used it to build steady rests to.

Re: Earls home made lathe

#7

Re: Earls home made lathe

Bob Fawcett

>Thanks Earl

Great job.

Re: Earls home made lathe

#8

Another home made lathe

Ruth Harding

>Mike Cunningham sent me this link.....it looks to be very easy to build....something even I can handle.

http://www.taunton.com/finewoodworking/SkillsAndTechniques/SkillsAndTechniquesArticle.aspx?id=26160

Re: Earls home made lathe

#9

Re: Earls home made lathe

Jim Terry

>Earl,

That looks fantastic, I've got to get over and see that.

Jim

Re: Earls home made lathe

#10

Re: Earls home made lathe

eaglesc

>Since I only make pens I am not a real turner.

that being said, thank you for posting this.

I doubt I will ever make my own lathe, but if I were to start turning bowls I would want one with a capacity such as this.

I cannot imagine the pride and satisfaction you will get when the first piece comes off this lathe.

Not only will it be a product of your own efforts but also the machine you made it on.

I cannot imagine anything more satisfying than that.

It is great to see a woodworker who doesn't have the need to buy every "new high dollar tool" thinking it will make him a better woodworker.

Thanks again.

Re: Earls home made lathe

#11

Re: Earls home made lathe

BAM

>SWEEET! Great Job! Take it for a SPIN and report back to US!

Re: Earls home made lathe

#12

Re: Earls home made lathe - caution

Pete LaBelle

>Just be careful of using pillow block bearings in this application. The housings are typically cast iron and not as rigid as a bearing pressed into a solid housing. A heavy out-of-balance load may cause one or both bearing to break out of the housings and have the load chase you across the floor.

Re: Earls home made lathe

#13

Re: Earls home made lathe

Jim King

>Earl: I find it interesting the worry about the bearings. I made this ugly beast a couple of years ago for $280 including the motor and have had no trouble yet using Chinese bearings. It works everyday. Obviously I did not take the time and effort to make it look so nice and professional as you did but it works and I have put some quite nasty things on it and chased it around the shop. Very nice work , congratulations. I think you will agree you will have more fun on your home made lathe than a super nice purchased one.


img

Re: Earls home made lathe

#14

Re: Earls home made lathe

Ruth Harding

>Earl, what did you use for tightening and moving the tool rest? Jim's looks like it's a little more involved to move it, your's looks like it is a quick action.

Thanks.

Re: Earls home made lathe

#15

Re: Earls home made lathe

Earl Kennedy

>I think the bearings will do ok.Cast iron is strong as long as it isn't hit with steel.The bearings are bigger than a lot of front wheel bearings in full size cars.Jim your lathe looks good to me.Made to do a job and it does it fine.You would be amazed how much better a little bondo and paint makes some thing look.This is the second lathe I have built.Ruth the tool holder is a quick lock made out of 2" square tubeing and flat plate.The main rod is 1 1/8" diameter and the off center pins in each end is 3/4" rod.The 3/4 rods are locked in the main shaft with split pins.The handle is off another lathe.The open design may be a problem with the shavings.If so I will just put a piece of sheet metal over it.Oh as I said I do have a 3520 Powermatic which I think is the best buy in a lathe bar none.I just like to make stuff and have another lathe in my head I would like to build.Ha

Re: Earls home made lathe

#16

Re: Earls home made lathe

Brent at Robust

>Earl, I think the bearings will be fine. John Nichols used pillow block bearings on his very large lathes and I personally know guys that spun 600 lb pieces of wood (of course they were larger than yours).

One nice thing that you did with your headstock design was to give yourself excellent access to the back of the work piece - nothing in the way - although I would suggest you put a guard around the shaft there too, just like you're planning to on the belts.

Anyway, very nice job. Have fun with it !

Re: Earls home made lathe

#17

Re: Earls home made lathe

Wayne Leach-NW Ontario

>Earl,

I am impressed with the simplicity and functionality in your design. As a machinery designer (before retirement) I have always liked to design my own tools and this has inspired me to get off my "duff" and do something about a bigger lathe. Let us know how you like it after you get to use it!

Wayne

Re: Earls home made lathe

#18

Re: Earls home made lathe

Ruth Harding

>Thanks Earl, I can't quite picture how to make it from your description but I will play around with it when I get to that stage.

I don't think the open design will be a problem...my old Nova has an open banjo....

Many thanks for sharing!