Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Burning a Natural Edge?

Posts

Burning a Natural Edge?

#1

Burning a Natural Edge?

George Van

>I have a natural edge bowl that the bark fell off due to spalting. I want to burn the edge rather than leave it "old brown cambium color" The problem I have is I do not have a detail type burning tool and as the bowl is turned to a finished edge I do not want to try a torch. Has anyone tried a simple soldering tool with good results? I have two soldering tools.

Re: Burning a Natural Edge?

#2

Re: Burning a Natural Edge?

John Lucas

>It's hard to use a soldering tool. It does work but it's awfully hot. You might try a magic marker. I have a friend who did that all the time. I use a propane torch.

Re: Burning a Natural Edge?

#3

Got torch?

Peter Teubel

>You can use just a regular propane torch. Turn the flame down as low as possible. Position the flame so that it's parallel to the edge as you go around and at a very shallow angle. Touch and go. The flame should scorch the edge but just flow over the side with little burning to the inside/outside. I tend to leave it, but you can always sand the scorching away for a cleaner edge.

Here's an early example:


Re: Burning a Natural Edge?

#4

Got torch?

Peter Teubel

>You can use just a regular propane torch. Turn the flame down as low as possible. Position the flame so that it's parallel to the edge as you go around and at a very shallow angle. Touch and go. The flame should scorch the edge but just flow over the side with little burning to the inside/outside. I tend to leave it, but you can always sand the scorching away for a cleaner edge.

Here's an early example:


Re: Burning a Natural Edge?

#5

Sorry for the duplicate messgage...

Peter Teubel

>

Re: Burning a Natural Edge?

#6

Brad Vietje

Re: Burning a Natural Edge? *LINK*

Brad Vietje

>George,

I used a pretty inexpensive pyrography pen, the Colwood Cub, which I got from either Packard or Craft Supplies USA. It costs about $60, and works well for signing work, too. The small tip, relative to a soldering tool, allows me to get into narrow crevases. There are also inexpensive woodburners with a narrow wedge tip, used for crafts, and maybe they would work, too.

Safe spinning,

Brad Vietje

Newbury, VT


img

Colwood Cub Woodburning Pen

Re: Burning a Natural Edge?

#7

Re: Burning a Natural Edge?

Troy German

>Also, Harbor Freight sells a "micro-torch" that uses butane for $10. It might be worth a try.

Troy

Re: Burning a Natural Edge?

#8

Re: Burning a Natural Edge?

Troy German

>Another idea - What about rubbing some candle wax or some other substance on the inside and outside of the rim before burning the top. That might keep the temp down on the parts you don't want to burn. Has anyone tried this? Did it work?

Just a thought,

Troy

Re: Burning a Natural Edge?

#9

Re: Burning a Natural Edge?

George Van

>Thanks for all the responses.

Peter, the edge is under an eighth of an inch and I am afraid the heat from a torch might be too much for this one as it is quite spalted in places, it may crack or catch fire.

Brad, I am going to get one of those so I have it available for future projects, it will be handy.

Troy, I got an email on the same subject, I am going to get one at Menards when I am at the store next.

John, I am going to try the magic marker, seems safe and I am already sanded to 600 grit it should save me a lot of additional sanding.

Re: Burning a Natural Edge?

#10

Re: Burning a Natural Edge?

Bob Fawcett

>Candle wax would catch fire.

Re: Burning a Natural Edge?

#11

Dick Hines

Re: Burning a Natural Edge?

Dick Hines

>I have a small torch that run off Ronson lighter fluid. The torch has a very hot fine point. Now if I could just remember where I got it.

Re: Burning a Natural Edge?

#12

Why Burn?

Juergen

>The odds are that almost any technique you use may have some collateral damage. In situation like this I've used a couple of products depending on the wood and smootness of the edge. A thick indelible Sharpie will work nicely in most cases. Kiwi makes a shoe/boot sole edge dressing and they even provide the applicator. The Kiwi product is essentially a black quick drying lacquer.

Re: Burning a Natural Edge?

#13

Re: Why Burn?

George Van

>I never made it to the shop, worked too late on the paneling project in the house, hopefully today.

Juergen, I will check out the Kiwi products display, I will try it while returning a roughed bowl, if it dries like lacquer it should work good without the problems of heat.