Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Introduction and question

Posts

Introduction and question

#1

Introduction and question

Randy Johnson Connersville, IN

>I�m new in this area. I�ve got a nice set up for flat projects, but at the present time the only lathe in the shop is a Delta mini that has seen very little use. So far, one small bowl and a few plugs and stoppers for powder horns. The bowl was made yesterday with the new chisels bought at the Cincy Woodcraft yesterday afternoon. Prior to that the lathe had not been even plugged in for over a year.

I think that may be about to change. I�m looking at various lathes. The new addition will probably be a Jet 16-42 with the zero speed ability.

While suffering sticker shock over what a good lathe costs (let alone what a GREAT lathe costs) I realize that it will cost a small fortune to get the tools needed to use the new toy. It seems that one area where a cost corner can be cut is by starting out using a faceplate and glue block in lieu of a chuck. The first question of what will probably be many is....

What glue is used for the glue block method? Please use brand names and not just a generic term. I�ve started reading up on the subject and one thing that caught my attention was a reference to separating the block from the project by turning off the lathe and using a chisel and mallet. None of the joints I�ve made in flat projects are going to separate that easily, at least not cleanly. Is there is something about this method I�m missing?

Re: Introduction and question

#2

Re: Introduction and question

Jorge Castaneda

>Welcome Randy,

I use Titebond II or III for my glue blocks, sometimes I use medium thick AC glue if I am in a hurry, but mostly Titebond II and leave the glue set overnight before I use the block.

Let the chips fly!

Jorge

Re: Introduction and question

#3

Re: Introduction and question

RevDoug

>What glue? There are several that you can use. Your wood glue that you use for the flat work will work just fine. Elmer's, Titebond, etc. are all good glues.

Seperation: If you want to break the joint instead of turning it off, use your wood glue on both surfaces and place a piece of brown craft paper (paper bag) between the two pieces. The joint will then come apart with a chisel fairly easily.

Turn 'em round,

Re: Introduction and question

#4

Re: Introduction and question

Ron in Drums PA

>Welcome to WC Randy

Faceplates are a great way to hold wood. Just about any type of glue will work depending on how quick you want to work.

White glue (Elmer's) and Yellow glue (many brands) work fine. I like to let this type of glue dry overnight. Since you do flat work you know you need perfectly flat surfaces.

Two part epoxy works well. When using the 5 minute kind I like to let it cure for a few hours.

My favorite is Cyanoacrylate (known as CA glue) you may know it as crazy glue. The type you buy in locals stores are a bit thin. I perfer a meduim CA Glue I don't like using an accelerator becuase I feel it weakens the glue. I let it sit for about 10 minutes before I turn.

Most importantly you need a good flat glue surface for any type of glue to hold. Most failures are the cause of poor joints, not the glue. Since you do flat work, you already know that.

Re: Introduction and question

#5

Re: Introduction and question

Peter Teubel

>" I�ve started reading up on the subject and one thing that caught my attention was a reference to separating the block from the project by turning off the lathe and using a chisel and mallet. None of the joints I�ve made in flat projects are going to separate that easily, at least not cleanly. Is there is something about this method I�m missing? "

===========================

That's right. The bottom does require cleanup after separation; either with some sort of reverse chucking method so you can turn the bottom to completion or just sandpaper.

Re: Introduction and question

#6

Re: Introduction & question - what Wally taught me

Carol from AZ

>I am a newbie turner as well. I took some lessons from Wally Dickerman, whom you will learn is one of the senior statesman over here. (In my book, "the"). :)

Wally uses 5 or 6 quarter alder for his glue blocks. It is clear and relative inexpensive, but perhaps poplar would be less expensive in your area. Wally is in Arizona and makes regular trips to the Northwest.

He uses a screw chuck or a face plate for mounting. He also uses medium thick CA glue and accelerator. The glue block and the work piece must have dead flat surfaces. Smear glue on one surface, spritz a little accelerator on the other. Smoosh (technical term here) together. Hold for a bit. Back on the lathe and have at it.

If I got that wrong, Wally will chime in here, after he gets home from the Desert Woodturning symposium this weekend.

Re: Introduction and question

#7

Re: Introduction and question *LINK*

john lucas

>Randy All of the above are correct. By the Way if you new to turning you may not know that CA is short for Cyanoacrylate glue of which Super Glue was the brand everyone knows but none of us turners use that brand because it's lousy. I use E-Z bond CA glue.

CA glue is expensive and titebond yellow glue works great if you don't mind waiting a few hours for it to dry. It works especially well with the paper joint mentioned above. On bowls I usually glue directly to the wood and then use a parting tool to cut the bowl from the waste block.

If you are going to turn green wood bowls titebond won't hold. I have used either CA glue or 5 minute epoxy for green bowls. A waste block isn't needed on green bowls if you just leave enough tenon for screws. Waste blocks are usually used when you don't have enough wood for a decent tenon to hold the screws.

For reverse turning see the link below and it will answer many of your questions. You'll have to click on the reverse turning link.


http://www.cumberlandwoodturners.com/tips.asp

Re: Introduction and question

#8

Re: Introduction and question

Jeff Myroup

>Randy,

Welcome to the site and the world of turning. I have the lathe you are thinking about and it is awesome. I would not recommend using a mallet and chisel to part your work. You take the chance of damaging the head stock bearings on a lathe you just spent alot of money on. You also take the risk of ruining the work you just spent hours on. As suggested it is best to part the work using a parting tool, don't go all the way thru and then use a saw to finish removing the piece. After that there are many ways to finish the bottom. Good luck.

Jeff

Re: Introduction and question

#9

I second what Carole says...

keith zimmerman, Normal IL

>Wally gave me the same advice via email a few years ago and it has never failed me. I use poplar instead of alser. Wally said it would work as well. I have not had a failure because of the wood.

One point I discovered about separating the block from the turning: Using a chisel to separate the two parts works quite well IF you remember to place the chisel on straight grain rather than end grain. End grain can split and ruin the wood and you might lose enough that you cannot turn a foot, or worse. And yes, there is some cleanup of glue residue.

Welcome to the wonderful world of woodturning. It is a magnificent outlet for creativity.

keithz

Re: Introduction and question

#10

Re: Introduction and question

Randy Johnson Connersville, IN

>If you are going to turn green wood bowls titebond won't hold. I have used either CA glue or 5 minute epoxy for green bowls. A waste block isn't needed on green bowls if you just leave enough tenon for screws. Waste blocks are usually used when you don't have enough wood for a decent tenon to hold the screws.

Actually that is one of the reasons for my sudden interest in turning.

There is a few acres of woods just west of the house that is currently being logged. They are dragging the logs up to the road and looking at the different species I figure what is left behind should supply me with enough raw material to turn for several years at no cost above gas for the chainsaw.

As an aside, I'm suprised at some of logs they are hauling out. Some are crooked beyond belief and a few are so small in diameter that they don't look like they would be worth sawing

Re: Introduction and question

#11

Re: Introduction and question

Jeff Myroup

>Randy,

Where is Connersville?

Re: Introduction and question

#12

Thanks All

Randy Johnson Connersville, IN

>As always WC is the place to go for quick GOOD answers.

There is a muzzleloading board I visit that doesn't have has many posts in a month as the boards here do in an hour.

Re: Introduction and question

#13

Re: Introduction and question

Randy Johnson Connersville IN

>About halfway and little north of a line between Cincinnati and Indianapolis.

Re: Introduction and question

#14

Re: My best recommendation is to...

Jamie Donaldson

>.. become a member of OH Valley Woodturners Guild(OVWG.org) that holds monthly meetings in the N. Cincy area, and the meeting this coming Sat. features demonstrator Betty Scarpino from Indy. Check the web site for details, but participating in an AAW chapter is a great continuing education opportunity, and the OVWG "Turning 2007" Symposium is well worth attending in Oct.

Re: Introduction and question

#15

cost of tools

Ruth Harding

>If you have been doing flat work for a long time you may have a stash of tools that have seen better days. Many people make their own tools either from new drill blanks and the like, or, reshaping other tools. Do a search on this site for many instructions.

I have also bought a couple of Forester (Forrest?) tools from kmstools.com here in BC that are about 1/3rd of the price of the regular brands out there. So far so good.

If you are able to invest in one chuck, they do expand and contract to cover feet of different sizes. I bough extra size chuck attachments over a while and worked with one chuck and one face plate for a couple of years.

hope this helps.

Re: Introduction and question

#16

Dick Hines

Re: Introduction and question

Dick Hines

>Randy, the real proublem you have is all the money you have tied up in flat work tools that you will never use again. Once you come over to the dark side you can never go back.

As far as a lathe in conserened don't start with a little lathe. Get one as big as you think you will ever need. You can turn little things on a big lathe but not big things on a small lathe.

Re: Introduction and question

#17

Re: Introduction and question

Bill Youngblood

>Hi Randy and welcome aboard. If you have a nice shop full of flat work tools, you might give some thought to segment turning. Your table saw and planer will never gather any rust. There will be a great segment instructor (Mark Kauder)at the OVWG symposium in October. Also, in segment turning I never use chucks. All work is done with faceplates and glue blocks. I use 5 minute epoxy from Lowe's and seperate the finished piece with a parting tool to the last little bit and then complete the cut with a saw. Hope this helps.

Bill

Re: Introduction and question

#18

Re: Introduction and question

Randy Johnson Connersville, IN

>Randy, the real proublem you have is all the money you have tied up in flat work tools that you will never use again. Once you come over to the dark side you can never go back.

Naw, I can see the possibility of turning becoming the larger percentage of what I do but there are too many people who want things made to ever get rid of the other stuff. Plus, I have hundreds of BF of cherry, walnut,and ash that were given to me by a friend who was moving and didn't want to haul it all. It needs to become something.

However...

The current project is 240 running feet of 5"X 1 1/2" handrails for the nursing home where I used to work. This is pure drudge work. No fun joinery, just cutting and shaping. After about four hours of it this afternoon I found myself turning on the little Delta again.

Re: Introduction and question

#19

Welcome, Randy,

Don Henthorn

>to the spinny side. Lots of good advice here and some, well-----OK, but all very sincere in wanting you to enjoy your turning. Most of the people on this site are younger than I am and they prefer chucks and all kinds of gizmos. I learned to turn before all these gizmos existed and I often prefer the old ways because that is the way I learned. I would urge you to refrain from buying a chuck and a lot of fancy gizmos until you have learned to turn well using glueblocks and find creative ways to do things that become obvious as you work with them. Then after you have gained some skill begin to analyze the way you work and what additional equipment you need to improve what you are doing. Just my take on things.

Re: Introduction and question

#20

Re: Introduction and question *LINK*

Bruce Wiseman

>Welcome Randy. Bill already mentioned the OVWG club, they are a great bunch of talented guys and you should hook up with them. Or if your up for the drive you would be welcome at the Central Indiana Club that meets Northwest of Indy in Zionsville. Club meetings are fun and a great way to meet up with people who will answer your questions and help you.


http://www.ovwg.org/

Re: Introduction and question

#21

Re: Introduction and question

Randy Johnson Connersville, IN

>You may see me at one of the Ohio club meetings some time. The deal in West Harrison looks interesting as well. My job takes me close to there every other month. (Bright, IN)

Re: Introduction and question

#22

Re: Dick's right about that...

Allen Neighbors

>I had a 10" table saw with an IncraJig System and a 3 1/4 HP Hitachi Plunge Router mounted in a Router Razer. Planer, shaper, and other flatwork tools. Built cabinets and other flatwork. When I started turning on a Grizzly, the table saw became just a table. I finally just quit taking flatwork jobs, and sold it. Bought a Oneway 1640. If I'd bought the Oneway first, I could have bought a couple of extra chucks with the money I spent on the Grizzly.

You said it yourself... "..after four hours, I found myself turning on the little Delta."

Sorry, my friend, I think you're hooked. :o)

Re: Introduction and question

#23

Hooray for Don

Bill Youngblood

>I totally agree. When I started turning an oldtimer told me that he had about 75 tools and gizmos and he uses about 5 of them. Now I'm the oldtimer and history is repeating itself. Find something that you really enjoy doing and go from there. Oh, and if we lived a bit closer, you would be welcome to try a bunch of old but slightly used tools. I have a drawerful.