Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

first time turning

Posts

first time turning

#1

first time turning

Sherri

>I tried my hand last night at turning for the first time.

My tool kept stopping the wood from turning, hanging it on the corners. What am I doing wrong?

Do I need to speed the lathe up? I tried easing up on the pressure tht I was applying.

Re: first time turning

#2

Re: first time turning

Mac

>Sherri, Try turning the lathe speed up a bit and also tighten the tailstock handle up a bit,check it for tightness once in a while. After you get the corners knocked off a bit, it will go easier.Enjoy

Re: first time turning

#3

Re: first time turning

David Breth

>It isn't so much doing something wrong as it is learning what to do. Sounds like you are working wtih a piece of wood that is square-shaped. I'm going to assume you are using a bowl or roughing gouge. Here are some hints

1) Sometimes (ok, frequently) it is better to use a bandsaw to knock the corners off first. Easier on you, the lathe, the tools, the toolrest, the wood, and reduces the possibility of a giant corner popping off the wood and into you.

2) Wear a faceshield.

3) Tool may not be sharp enough. Sharpening is a topic unto itself. Lathe speed helps, but it won't cure a dull tool. If you are working a square piece, you don't want to get too crazy with the speed, because improper presentation of the tool to the work can cause a lot of bouncing, bamming, and an unsafe condition, and you haven't got a level of experience to let 'er rip. General rule would be never to exceed a speed that you feel comfortable with.

4) You may not be presenting the bevel of the tool to the work. This is really difficult to explain, I'll try but other people will do FAR better at it. When you look at the tool in profile, you'll see that the cutting edge has a "flat" on the bottom, aka the bevel, or cutting edge. As you raise/lower the handle of the tool, and therefore change the way the cutting edge is presented to the wood, you'll see it cut differently - some angles it will just beat the wood to death, producing dust, chunks, or nothing at all, but as you near the bevel angle, you'll start to get chips that look like something, and you'll make progress on the wood. With a square piece of wood, it isn't always easy to know if you are "riding the bevel", but as the wood gets rounder, if you are riding that edge, you'll start to get nice long shavings.

5) Height of the toolrest. You may be too high or low to present the bevel properly to the wood. If it were me, I'd recommend putting the toolrest at about the same heigh as the center point of the headstock and go from there.

6) Proximity of toolrest to wood. You want to be as close to the wood as you can get (and confirm that the wood can revolve without hitting the toolrest before firing it up). This will minimize bouncing, flexing, etc., and allow you a more steady cut once you do find the bevel to ride.

6) If you've got somebody near you who can help with hands on, or a turning club nearby, it is super-valuable. An hour of hands on help can go a very, very long way to helping you get your feet, and can help you make sure you're working in a safe way.

My 2-cents, but you've got change coming.

David B.

Re: first time turning

#4

Re: first time turning

Troy German

>If you are using a lathe with a reeves drive that hasn't been maintained it could be that the motor's pully is stuck causing the belt to be loose and slip.

And I'm sure you'll hear this a lot, but wear a face shield

Be safe,

Troy

Re: first time turning

#5

Re: first time turning

Jeff Myroup

>I agree with Mac, If the wood stops turning even with light pressure from the tool, sounds like the wood is spinning on the spur drive. Check the spur drive end and see if it is creating a hole like a drill. if it seems like that is not the problem then it has to do with tool presentation. Just be careful tightening the tailstock to much as this can cause early where on your headstock bearings. Other than what is already mentioned. I would recommend taking a couple classes. The Woodcraft store near me offers a couple day course for introductory turning and that would help you alot. I think the last one I saw was about $75.00

Jeff

Re: first time turning

#6

Brad Vietje

Now that's excitement !

Brad Vietje

>Hurray for you, Sherri -- you must be grinning now !

There could be a few different reasons, but sometimes the drive spur can spin and create a little depression. You would then take it out, clean out the shavings (spur isn't such a great drill), then tap it in place with a good rap or two with a mallet before re-mounting on the lathe. The tailstock can be snugged up, but not super tight, which will hurt the lathe.

The best advice anyone ever gave me when I started was to push the tool against the rest, not the wood.

Safe spinning -- and have fun !

Brad Vietje

Newbury, VT

Re: first time turning

#7

JL

Re: first time turning

JL

>In addition to all the good advice above...

Typically when I "prepare" a piece of wood for turning, I use a center punch (a nail would work also) in the end where the spur drive goes. I then take the spur drive from the lathe and hold it on the piece and give it a "whack" with a wooden mallet or other piece of wood. This is to "set" the spurs into the end. I then put the spur drive back in the headstock and chuck the piece of wood in. Align the spur "holes" and gently snug the tailstock into the other end.

Now that I have a Sorby Steb Centre, I just use the punch and mount the wood on the lathe.

Re: first time turning

#8

Re: first time turning

Barbara Gill, Remlik VA

>Sherri, where do you live? One of us might be close enough to help.

Re: first time turning

#9

Re: first time turning

Bob Fawcett

>Great!

You've gotten lots of good advice.

If you have a digital camera, take a picture and upload it so we can see the setup and the wood.

If not let us know if the assumptions made are correct. Try some of the tips and post again.

Re: first time turning

#10

Re: first time turning

Robert D. Macgregor

>I have had slippage from loose belts and also had the spur drive rip out the wood. One other possible source of slippage that I haven't seen mentioned yet is that some lathes have a set screw on the pully cluster that must be tight or the cluster will slip around the lathe drive shaft. It turns fine with no resistance (chisel) applied, but hangs up right away with any significant pressure on the wood. It is worth a look.