Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Chainsaw repair question PIC

Posts

Chainsaw repair question PIC

#1

Chainsaw repair question PIC

Mike Rubes, Apex, NC

>Hi all,

I probably should have sub-titled this one as a "stealth gloat", but I really do have a repair question first.

The chainsaw I've been using is a Husky 141. Long story short is that one of the two nuts that hold the bar on has somehow become stuck in place and I cannot remove it. It is like the nut is just fused somehow to the bolt. This story involves loaning the saw out and an attempted repair made in good faith. I've no problem with the attempted repair and in fact, it will turn out ok for me in the long run :) To the problem, when I try to turn one of the nuts that hold the bar in place (loosen or tighten), the entire bolt stud rotates as well! I suspect that the nut was not the same thread size as the bolt and was forced on, but I don't know for sure. Clearly, though, something is stripped inside. The other nut/bolt works fine, but I am surely not going to run the saw with only one of the bar nuts tightened down. The one that causes the stud to spin is not even tight against the bar. If I loosen the good one, the bar is very loose. This has been an OK saw, but has given me a few other problems, but none of them have kept me from using the saw until now. So, I need to know how to get that stud out. Hopefully, I can do this without taking the saw completely apart?

Sooo, long story short (and an early happy ending) was that this latest mishap with that saw and the fact that I had some birthday/Christmas money left over convinced me to go ahead and pull the trigger on a new Stihl 250!! :)



After playing with the Stihl a little bit, I really like it. It cuts smooth and seems to run like a champ. I went with the 18" bar on it. No complaints so far at all.

Still, I would like to make the attempt to fix the Husky myself. Brand new that saw was only around $200 and I would much prefer not to spend that much again in a repair, so I would like to try it myself. So, if you happen to know how to get access to the bar bolt and get it off, or could offer advice, that would be great!

Thanks in advance,

Mike

Somehow ended up with TWO chainsaws in Apex, NC!!!

Re: Chainsaw repair question PIC

#2

Re: Chainsaw repair question PIC

Jorge Castaneda

>Hi Mike,

If you can remove the damaged stud and just discard it, get a new stud and nut and put it back together. You may need a special tool to seat the stud home.

I love my Husky, so try to save it.

good luck

Jorge

Re: Chainsaw repair question PIC

#3

Re: Chainsaw repair question PIC

Ruth Harding

>Mike, there are gizmos for cutting nuts, try your local hardware store......other than that, have you taken the casing off? I would do that and shove a screw driver -flat head, or the flat end of a nail puller under teh nut....if it loose enough to give you some wriggle room for teh tool. Then I would 'lift up' and put pressure on the nut. With the pressure lift on the nut I would at the same time try and open the nut again....or, if you can get underneath with a hacksaw blade just cut the bolt...or use a dremel to cut the nut off........or...or..

Re: Chainsaw repair question PIC

#4

Leo Van Der Loo

Can you get in there with a dremel cutoff wheel,

Leo Van Der Loo

>If you cannot get behind the nut to cut the bold with a hacksaw blade or if you don't like to do that, you could split the nut with the dremel cutoff wheel on the diagonal and just cut into the bold thread.

Have fun and take care

Leo Van Der Loo

Re: Chainsaw repair question PIC

#5

Re: Chainsaw repair question PIC

Dinyar Chavda

>Folks:

The man wants (make that "needs") a new chainsaw. He has found an excuse (oops, sorry, "rational reason") to get one! Don't take it away from him!

By the way, Mike, what are you going to do with the old chainsaw? (Hint, hint!) :-)

D

Re: Chainsaw repair question PIC

#6

Re: Chainsaw repair question PIC

Mike Rubes, Apex, NC

>Hi Dinyar,

HA!! You hit the nail right on the head! I'd wanted a Stihl for some time, so it really didn't take much of an excuse to get one :)

I am going to try to fix the Husky, thanks to all for the ideas. I think the dremel is the best bet. If I can get it fixed, I've got a buddy who is a turner who doesn't have a chainsaw, so I may give it to him.

Really like my new Stihl!! :)

Mike

Looking for logs in Apex, NC!!