We value your privacy.
We use cookies to enhance your browsing experience, analyse site traffic, and personalise content.
By clicking “Accept all”, you consent to our use of cookies. You can also choose
“Essential only” or learn more.
>The weak point in my bowl finishing is the bottom/foot. After hollowing, I've been either reverse chucking with a jamb, supported by the tailstock, or parting off above the chuck. Neither method allows free access to the base for a nice finish and shape. I can chisel the bit that was blocked by the tailstock and hand-finish, but I'd like access to the whole bottom while it's on the lathe. So... What do you folks use? Vacuum chuck? Cole jaws? I've read a bunch about it, but I'm curious what you guys do in practice.
>but for me, the jam chuck and a little chisel clean up is just faster. Plus I think it's nice to do a little "manual" labor on each piece. Keeps me close to the wood and the grain etc.
>I have cole jaws and vacuum chucks. I usually reach for the vacuum chucks. If money is an issue cole jaws, longworth or donut chucks are good options.
Most of my bowl bottoms a just slight concave. I often hold the bowl against a "sort of" jam chuck. Really a tappered block of wood on a dedicated face plate. I use a 1/4" gouge to finish as much as I can and then use a narrow parting tool to remove as much of the "pip" as I can. Then, with the lathe turning about 100RPM I take a carvers spoon gouge and apply gentle pressure against the "pip" at the bowl bottom. When the pip stops rotating you've severed it and as you gently remove the spoon gouge everything still will hold against the jam chuck. Stop the lathe, hold the bowl and slide the tailstock back to remove the bowl. Then sand as necessary. Don't but that spoon gouge in twice or it will all come loose. DAMHIKT
>I use a vacuum chuck whenever possible. If the piece has holes in it so I can't use vacuum, I use a jam chuck made on a decicated face plate and a 4" schedule 40 pipe coupling (avaliable at Lowes or Home Depot or any other place that sell plastic plumbing pipe).
>Pat Check out the link below and go to "reverse turning bowls" You will find a lot of choices. The only thing I don't have on there yet is the Longworth chuck.
>Pat, I do just like Cyril has described. Most of what I have been turning lately won't fit on cole jaws or be held with a vacuum anyway. At a recent meeting, one of the other guys asked me if I ever turned anything that didn't have holes or cracks in it!
>I used a compression (donut) chuck initially for a few years. Once I got my vacuum chuck system bought/made it is vacuum all the time unless the piece won't hold a vacuum. If I can't use the vacuum, now I often just put the bowl over the drum chuck (pump off) and bring up the TS and finish it down to the little nub which I remove off the lathe.
While the compression chuck is not as convenient I must say that it did work well and is a lot easier to make than a Longworth.
>I have a vacuum chuck but don't use it for shaping the bottom of the bowl. At least not much. I find it tough to center the bowl up reliably. I use the vacuum shuck a lot for sanding and finishing though.
I made a set of "grippers" for my Cole jaws that are metal straps bent slightly past 90 degrees. I hold the straps to the jaws with the original rubber buttons. They are about three inches long and extend the reach of the Cole jaws out to the full 16" swing of the lathe. They work much better than the rubber buttons. When I turn a bowl I rough the outside, then finish the inside and the top inch or two of the outside (to give the grippers a finished surface to hold onto). Then reverse it into the Cole jaws and finish roughing and sanding the rest of the bowl. I have a large pair of "scissor" calipers that allow me to reach between the plates of the Cole jaws to check the thickness all the way to the center of the bottom.
I have also done jamb chucks and cut the nib off the bottom. Sometimes I chuck a sanding disk in the drill press and just set the bowl on the DP table and bring the disk to bear.
1. Turn the jam chuck to fit the bowl. It doesn't have to be an exact fit.
2. Hold the bowl up against the jam chuck with the tail stock.
3. Wrap masking tape over the bowls edge and around the chuck real tight in a cris-cross motion. Keeping the tape tight is the key to making this work. Use enough tape to feel safe.
4. With the tail stock still in place, start turning the bottom of the bowl until you have a little nub or the center is in the way. Move the tail stock out of the way and take light cuts towards the head stock until the nub is gone. Then take a light cut across the bottom, add a couple of detail lines with a parting tool and sand.
I'll look to see if a have some photos of this method tonight when I get home from work. I use this method when I demo because it's quick and easy.
>My cole jaws hold up to 11.5" or so. Between 12"-15.5", I'll jam chuck with tailstock support. Above 16", I use a doughnut chuck.
All three work great, with the cole and doughnut chucks giving me full access to the bottom of the bowl. The Jam chuck always leaves a little pip that I remove with a chisel and sand flush.
>Check back through Allen's postings. I made a copy of his rubber band clamp donut chuck. It does a wonderful job for much less money, space and hardware than vacuum. Like all donuts, not good for uneven (like NE) rims, but hey, I'm still practicing fair curves on basic bowls. All it cost was the price of faceplate and some plywood scraps.
>Pat, I use a very low-tech solution. Others mentioned using a jam chuck with tape. Instead of the tape, I use three or four 1-inch dia. fender washers or similar-sized scraps of 1/8 inch plywood. I screw these to the jam chuck next to the edge of the bowl so that one side of each rests against the bowl and the other rests against the jam chuck. The washers are distributed roughly equally around the bowl. If you use fender washers, pad them with a bit of tape to avoid scaring the bowl. If you have a screw gun this is faster than taping the bowl and is more solid. Dennis
>For small items I try to use the vacuum chuck. When the vacuum chuck won't work I usually reach for the hot glue gun. If the piece is sanded smooth the cold glue can usually be rolled off the wood with finger pressuse. Warming slightly with a heat gun will give better results but only if warmed slightly.
It depends on size, shape and where the wind blows
Leo Van Der Loo
>from, I use, Chuck with the regular jaws or the rubber cole jaw bumpers on there, then cloe jaws, vacuum if that's possible, donut type jaws or just wooden faceplates with saran wrap around or some wood blocks screwed on to keep the bowl on, just depend on what it takes, and how I feel, (lazy or not) ;-))
>For bowl bottoms I use a sanding pad on a holder on the bowl lathe or the drill press and work the bottom against it, going through the grits until satisfied. I have attached a link to the process. One of these days I need to make a site map. If you follow the tool making links there is also a page on making a set of Cole jaw copies for your chuck.
Re: Have a link to this rubber-band idea? Thanks.. *LINK*
Bruce Wiseman
>This is from Keith Tompkins visit to the CICAAW club for a demo, the pic shows a kind of rubber band chuck, not a donut like Mike is talking about but it worked for Keith.