Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Holding Water

Posts

Holding Water

#1

Holding Water

Georg Waldhof

>Ok - here's my bizarre question of the day:

Anyone have any experience turning wooden bowls to hold water? Specifically, I'm thinking something that needs to hold about 3 to 5 gallons of water for as much as 30 hours.

I figure I need:

- close grain wood (not oak) with well sealed glue joints

- waterproof glue

- a big lathe.

I have all that. What sort of sealant would be good? I'm wondering how Spar varnish, or even paint might hold up? This does not need to be food grade or anything since no one will be eating or drinking out of it. What about catalized laquer?

Thoughts and suggestions? Right now I'm thinking of gluing it up out of cherry, mahogany or makore, turning it and sealing everything up with spar varnish.

Thanks

George

Re: Holding Water

#2

Steven Antonucci

Sorta-

steve antonucci

>I turned a bowl out of Yellow Poplar that was about 14" in diameter. It was an experimental bowl, and was not glued, but received MANY coats of finish. When I was done with it, I placed it on a rock in the driveway.

Since then (at least a year), the bowl has been rained on, frozen and thawed, and baked with no ill effects. If it rains, it still fills up, and I dump it out if I think of it.

At this point, it has a coat of just about every thing commercially available on it, so I can't offer you much in the way of a recipe...

Steve

Re: Holding Water

#3

Re: Holding Water *LINK*

joaz

>Hi George, I am currently working on a mahogany sink for a guys boat. He plans to use epoxy to seal it. Should work.

I use several coats of spar varnish on goblets and it works well.

Why 30 hours??

Joaz


http://www-maine-web.com/woodturning

Re: Holding Water

#4

Re: Holding Water

Jorge Castaneda

>In my photographer days, I made a very large sink to hold the trays out of plywood and used a layer of woven fiber glass and set it with epoxie, and a second layer of epoxy, it has had on it hot and cold water and all the chemicals and my ex still uses it 40 years later.

Re: Holding Water

#5

Re: Holding Water

Terence Rice

>I have made several flower pots for my wife. The oldest is four years old and still holds water without leaking. On the inside I used Enviro-tex, an epoxy finish avaliable at Micheals or Craft Supplies. It is the stuff that is meant to be used as a pour on finish for table tops. The only problem is that it is a bit slow setting up and you have to keep turning it slowly so it doesn't all run to the bottom.

If anyone knows of an accelerator of on a faster set up product I hope they will let us all know.

Re: Holding Water

#6

Re: Holding Water

Jim King

>Here is a table side beer cooler glued up of 3/4 KD boards turned and with about 50 coats of wipe on high gloss floor grade polyurethane on the inside for waterproofing . Works great and no sign of water stain or damage. I also use the same on wine glasses .


img

Re: Holding Water

#7

Re: Holding Water

Georg Waldhof

>oooo - very nice work! The nicest beer cooler I've yet seen.

Many thanks - lots of good direction in the answers, but your photos are inspiring.

George

Re: Holding Water

#8

Jack Daniels

Ron in Drums PA

>Jack Daniels is aged in white oak barrels. So is wine. For a bit longer than 30 hours too!

No glue is used, it's the way the joints are cut and the swelling of the wood that prevents the kegs from leaking.

Food for tought

Re: Holding Water

#9

cedar buckets

john lucas

>Cedar buckets are essentially made the same way the oak barrels are but without a top. If you made a sink this way it might leak a little after a vacation when it hasn't been used in a while but would seal up pretty fast when you first run water in it. don't know how many people would put up tith that.

Re: Holding Water

#10

Re: cedar buckets

Peter Hyde

>I once dismantled a 16ft. cedar hot tub. It was made from cedar 2x6 with tongue and grooved edges and held together with 1" round iron hoops with a thread and sleeve connector. Bottom was just the same boards laid flat and cut into a circle with a continuous tongue that fitted into a groove at the bottom of the side planks. It was a demo model inside a store and had held water for about 5 years with no leaks.

Re: Holding Water

#11

Re: cedar buckets

Barry Irby

>Saw a guy on TV making waterproof boxes. He pounded a nail or small rod into the edge of the board, making a groove. Then they planed the edge down to the bottom of the groove and assembled the box. When the water seeped into the joints the wood compressed by the nail expaned and made a good tight contact with the adjacent board and a water tight joint.