Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Beale buffing system

Posts

Beale buffing system

#1

Beale buffing system

C Yawn

>I have been reading, and viewing, with interest the results of wax buffing turned items as a final finish. Pretty sure I will be getting the Beale buffing system. I have their catalog and have read about the different types and attachments. Ya'll got any tips, tricks or traps advice on using this finishing technique?

Some questions I would like read about:

Are there any other brands of buffing systems to consider/avoid?

I envision using the buffs for all types of turning (spindle, goblets, bowls, platters) - looks like I will need the flat and rounded buffing wheels?

Which is more useful - the three-wheeled lathe-mounted buffs or the 3 wheels on separate shafts?

Is there a hand-held technique that works? Like leaving the turned item on the lathe and chucking the buff wheel in a drill.

Thanks for the help. Charles

Re: Beale buffing system

#2

Re: Beale buffing system

Sean Troy

>When you first get the wheels, spin them up on the lathe and hold a hacksaw blade to the wheels for a min. or so. This cleans off all the loose fibers and it will make a mess. When you use the Carnuba wax,USE VERY LITTLE.i would reccomend the seperate wheels to be used one at a time.

Re: Beale buffing system

#3

Re: Beale buffing system *LINK*

Bob Fawcett

>I have the Beale and recommend it. Get the 3 separate wheels and one of these long adapters to use on your lathe. The long adapter gives you access to places you can't reach with the 3 on a lathe system.


Long adapter.

Re: Beale buffing system

#4

Ric Taylor

Re: Beale buffing system

Ric Taylor

>I have the Beale system and I like it a lot. I have the system that allows mounting all three wheels on the lathe at the same time, as well as a set-up to mount one wheel at a time.

Mounting all three wheels at the same time is only good if you are buffing small objects. If you try to buff a medium or large turning, you will find that while buffing on one of the wheels, the other two wheels will be in your way, because they are too close. I haven't used the three-wheel mount in a couple of years because of that. I just mount one buffing wheel at a time, it only takes a few seconds to change from one wheel to another.

When your wheels are new, there will be a blizzard of fuzz and lint all over your work area. This will mostly go away after you have used them a few times.

I strongly recommend wearing a dust mask any time you are buffing. If you don't, you'll be breathing in some of the dust from the wheels, and even small amounts of the buffing compound, which is all bad for your lungs.

Hold on to your turning securely, when the wheel grabs on to your turning, it will be launched across the room so quickly you won't realise what happened.

Ric

Re: Beale buffing system

#5

Re: Beale buffing system

Cyril Griesbach

>I use the bowl buffs on a #2MT right on the lathe. I have the 2" and 3" sets and there are times I wished I had the extension adapter as well. I'm very happy with the system.

Cyril

Re: Beale buffing system

#6

Re: Beale buffing system *LINK*

Stuart Johnson

>I made up a 3 wheel buff for about half the price of Beale's. I think it would be easy enough to also make up individual buffs at what ever length you want. The file contains a good web site for buffs and polish.

I'm not trying to down play Beale's product because I do use their individual ones with the #2 adapter. I have found it is best to use a 1/4" bolt to hold it in the headstock.


3 wheel buff

Re: Beale buffing system

#7

Re: Beall buffing system

Russ Babbitt Jr.

>I have the complete set of Beall systems. The 3 wheel setup as mentioned is useful for small items. Larger items do not have enough clearnce to buff safely. I also the buffs mounted on an external motor as I find the ways of the lathe interfere with some large pieces. After you have "charged" the wheels with compound use a very small amount each time you buff. Just about one second of light contact I think is enough. Be aware of how much pressure you use. The first two compounds are abrasive and can remove a previously applied finish. To anwer another question I have to say that Don Pencil sells a copycat system.

Re: Beale buffing system

#8

Re: Homemade buffing system (Long)

Allen Neighbors

>Charles, you asked, "Are there any other brands of buffing systems to consider/avoid?". One is to make your own. I did.

I picked up a used 1725rpm motor and reversed it to turn CCW (this direction keep the wheels screwed on). Bought an arbor that is normally used to mount a grindstone on the motor shaft. I extended the arbor, by rethreading 1" of the end to fit a 1/2" long nut. Installed the long nut - tight - which left 1/2" of threads to mount a buffing wheel.

I made my four buffing wheels (8" dia) by cutting a 1" stack of 8" circles of each material: Cotton-Denim/Polyester-Denim/Cotton-Flannel/Felt. (While I was recuperating from a heart attack) :o)

I mounted the 1" thick homemade wheels on 1/2" machine bolts with washer and nut.

I mount these wheels into the end of the motor shaft.

Wonderful! Price of the used motor, 4 bolts, a motor arbor, and a long nut.

My wife is a quilter, so she gave me the material.

Re: Beale buffing system

#9

Thanks for the advice folks. Charles

C Yawn

>

Re: Beale buffing system

#10

Good going Allen!

Clem Wixted, Jonesboro, AR

>I like shop made tools and this is a great idea.

Were you fussy while cutting the 8" circles and punching the hole for the bolt?

Clem

Re: Beale buffing system

#11

Re: Was I fussy!?!?? You said it!

Allen Neighbors

>I was griping the whole time... couldn't lift over 5 lbs for 8 weeks, and they had sent me home bleeding internally...

Just kidding... I know what you meant. I had an 8" dessert plate that I used for a template, and cut out one disk of cardboard (after I could go to the shop) that I drew with a compass, so I had a true center for the hole. I drew around the plate on the material with a ball point pen, pinned a few together, and then cut out three or four layers at a time.

I drilled the 1/2" holes in the wheels on my drill press. It was sort of fuzzy when finished, but I threaded the bolts through.

When I got the circles of material cut out, I sewed them together with an upholstery needle... got them too tight, and had to rip out some of those oversized stitches after I discovered they were too stiff while buffing.

I used the Felt with Tripoli; The cotton/polyester mix with White Diamond; The 100% cotton denim with Carnauba; The flannel is used clean, if I think I need it.

I've since made a couple of buffs that I use on smaller bowls, and I made another cotton denim wheel that I use strictly with Bees Wax.

I mounted the motor on the corner of a table, and padded that corner with a scrap of carpet, so if I bump it with a large bowl it's not marred. It's a really good system. If you want, email me, and I'll try to send you a picture of it. :o)

Re: Beale buffing system

#12

E-Mail on the way!

Clem Wixted, Jonesboro, AR

>