Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Intentional Warping Follow Up

Posts

Intentional Warping Follow Up

#1

Intentional Warping Follow Up

David Breth

>A couple of weeks ago, I posted a message about intentional warping, got some advice to what I had already experimented with, and continued my experimentation.

At the time of those warping posts, I had this guy drying, and thought I would let you know how I did this, as I was super-pleased with how it turned out. (Though please note, I am perfectly happy to accept any criticisms, 'cause I'm looking to get better).

This was a sealed over branch that looked like a small burl. I cut it off and let it start drying after anchor sealing. Not sure how long it dried, probaby two months. As I turned it, the branch center popped out. I suspected that might happen, so I made sure that part was not the center of the bowl, or else I would end up with a lampshade instead of an interesting inclusion! It wasn't an issue, but - always wear your faceshield.

I turned it to about a quarter inch thickness, as evenly as I could considering the rather squared exterior bottom. I can't quite describe the shape I turned....the exterior edge is actually a bit lower than part of the interior of the bowl. Kind of like a vase top that flows way over and cascades down a little bit. My thinking was that the branch, shape, and thickness would lend themselves to creating a cool warp.

I sanded it to finish (600 3M for me), then paper-bagged it with its' own shavings. Let it sit for a month or so, looking in on it periodically because the suspense was killing me. Decided it was dry enough at some point, lightly sanded to the little raised fibers, and started finishing. Minwax Antique Oil Finish, probably seven coats before I was happy with it. (Recently I've been putting a coat of deft on before the oil, but in this case I opted not to. Seems to have left more red in the wood).

Interested in your thoughts. I've turned another one since that was also a sealed over branch (hard maple) and therefore also has the hole, slightly different shape. Looks pretty slick, with some feathering. Could become a habit!!

This piece is maybe six or seven inches diameter, the maple one slightly smaller.

Sorry about the terrible photograph on the sideview.

David Breth


img

Re: Intentional Warping Follow Up

#2

Re: Intentional Warping Follow Up

David Breth

>Sideview.


img

Re: Intentional Warping Follow Up

#3

Consider this.

Keith Newton

>David, I have thought of taking this approach, and have given it more than a little thought. Somthing to consider is that all woods are not equal in how they would react if they were very similar in grain-pattern.

If you have access to tables that show the ratio between tangental, and radial shrinkage. Not only would the results be greater for the ones with the highest ratio, it should be noted that the total amount of shrinkage from green to dry on certain woods have a greater value of each besides the ratio between them.

One such wood is Pacific Madrone. I am sure you have seen how Christian Burchard has been taking advantage of this property in this wood.

Some other woods that seem to have good numbers are Overcup Oak, and Southern red oak, and black willow.

Besides the ratios, it would be good to have other properties, like hard to splitting, and fine even texture, as opposed to coarse ring porous.

Then wild changing grain direction, as in burls, and especially in relation to looking into the end-grain relative to the arc of the annual ring.

If you study, and learn to find wood with these properties, then you would do well to turn green, and thin, so-that it can distort more freely.

If you try to dry the wood before it is turned, the wood memory can take a set, and will not change like it will going from green to dry with no restraint.

I thought I had a link to the US Forest Service handbook, but couldn't find it. You can find a list in Hoadley's "Understanding Wood."

Re: Intentional Warping Follow Up

#4

Sweet! I dig it.

Pat Taylor

>

Re: Intentional Warping Follow Up

#5

Re: Intentional Warping Follow Up

Allen Neighbors

>I think it's awesome. Good work! :o)

Re: Intentional Warping Follow Up

#6

Re: Intentional Warping Follow Up

Troy German

>That came out great! Thanks for posting the whole process. It waas very interesting.

Troy