Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Question for mini lathe owners

Posts

Question for mini lathe owners

#1

Question for mini lathe owners

Joe in a Cleveland suburb

>Hi.

Can you tell me about your setup as far as what you have you lathe on? Is it on a stand? Bolted down to a bench?. Any added weight? Those kinds of things.

What about height in relation to your body - where is the center of the item you are turning?

Thanks,

Joe

Re: Question for mini lathe owners

#2

Re: Question for mini lathe owners

David Breth

>The stock response for lathe height is the center point should be about elbow height. The follow-up response to that is "wherever you find it to be most comfortable."

I'll semi-defer to other people for their mounting methods, other than to say you want to mount it in such a way that you have not compromised your ability to have physical access as you move around, and such that it doesn't have much opportunity to wobble around. I haven't used my mini in a while, but I pretty much had a terrible setup - it was mounted on top of one of those craftsmen portable workbench deals. Height was good for me, but the legs flexed a lot with an unbalanced load.

David B.

Re: Question for mini lathe owners

#3

Re: Question for mini lathe owners

john lucas

>Joe I currently have 4 mini lathes. 3 are on thier own stands mounted about an inch above my elbow height. The 2 jets are on lightweight stands that add weight to after moving. The Nova is on a permanent stand with drawers to hold stuff for that lathe. The Carob-Tec is my traveling lathe. It is on a stand that is 11" tall and sits on folding stand. This makes it easy to haul with me when necessary.

Re: Question for mini lathe owners

#4

Re: Question for mini lathe owners

Curt Stivison

>Joe,

I have a Jet mini that I have mounted on a Jet stand. I have not had any trouble with it but I have only been turning about a month. Stand is set as low as it can go, about elbow height.

CW

Re: Question for mini lathe owners

#5

Re: Question for mini lathe owners

Bill Youngblood

>Hi Joe,

Our club has a Jet mini mounted on the Jet stand. It works just fine. I have a Jet mini mounted on a portable bench. I countersunk holes in the top of the bench to set the rubber feet of the lathe into just to keep it from walking away. It works fine also.

bill

Re: Question for mini lathe owners

#6

Re: Question for mini lathe owners

Pat Taylor

>I'm new, but my Jet mini on the Jet stand feels mighty sturdy, and doesn't do "the walk" until I load up a 9" diam. x 10" tall non-rounded wet blank.

Re: Question for mini lathe owners

#7

Re: Question for mini lathe owners

gil jones

>Joe, the spindle center height is 45.5", and I am standing on a .5" thick anti-fatigue pad (which works for me). The bench is all wood (painted gray), a 2" thick top, and weighs about 250 pounds (without the lathe). No extra weight added. The lathe came with padded feet that adjust up/down, and there is one 2.5" deck screw going diagonally through each leveling/support foot and into the bench top. So six deck screws hold the lathe to the bench, and that seems to work well. If it is shaking too much, I slow it down (sure would be nice to have EVS).

Gil


img

Re: Question for mini lathe owners

#8

Thank you.

Joe in a Cleveland suburb

>

Re: Question for mini lathe owners

#9

Re: Question for mini lathe owners

Tom Wilson

>I have mine mounted on one side of a board, a scroll saw is mounted on the other side. I can rotate the board and use either the lathe or the scroll saw (I have a very small shop). the whole thing is on wheels to push out of the way when I am doing something else. I also have to sit down to work, having back problems that won't allow me to stand for very long.