Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Reverse chucking a hollow form

Posts

Reverse chucking a hollow form

#1

Reverse chucking a hollow form

Carole Valentine

>Seeing Jen's post about cutting it close when she was parting off a small hollow form prompted me to take some pics that might help some of the beginners save some knuckles. (Jen is an advanced turner and she likes to live dangerously!) If you never throw away your chuck "orts" (leftover pieces from the chuck), you can use them to reverse small hollow forms and finish off the bottom. I have a whole box of these that I use constantly until there is nothing left of them. Just throw one in the chuck, turn it round and shape the cone part to fit your vessel. If the piece wants to slip, it helps to put a small piece of rubber or leather with a X cut in the center over the tip of the cone. I have a parting tool that has been ground at a slight angle rather than straight across which allows me to part the piece with a concave bottom. I usually take it down to about 1/8" then use a little saw to complete the parting. The nub is quickly removed with a small carbide teardrop bit in a Dremel, power carver, or similar tool then sanded. The little vessel in the pic started life as a 3" cube between centers - no glue block, faceplate or woodworm involved. The tenon on the chuck ort was turned to allow the neck of the vessel to fit snugly but rest on the shoulder of the tenon. This method is for light cuts only and be careful not to put too much pressure on the tailstock to avoid cracking a thin vessel.


img

Re: Reverse chucking a hollow form

#2

Bob Moffett

Re: Reverse chucking a hollow form

Bob Moffett

>Thanks for the pictures. That helps me a lot. As I understand it you are basically using a jam chuck on each end. How would you do this if you had collar on the top shaped like the end of a trumpet (flared out)? Would you make a smaller jam chuck for the trumpet end?

Re: Reverse chucking a hollow form

#3

Re: Reverse chucking a hollow form

Greg Haugen

>I don't hollow often. Don't have the time to. But when I do I really like my "Woodchucker Mandrel" from Craft Supplies. New Catalog, page 49-top corner. The features are it has a 2MT so no chuck need, the you can turn a cone any size and have it on the faceplate, a power sanding mandrel is placed in the other end to seat against the bottom of the vessel-I use a 1" pad for the smaller openings, and then the tailstock is brought up to have bottom. This gives you three point of contact on the vessel and its very stable. If the walls are thin there is little risk to damage the vessel.

It's also not that expensive.

A nice surprise when I got mine. It's not mentioned but its made by Kelton Industries.

Greg

Re: Reverse chucking a hollow form

#4

Re: Reverse chucking a hollow form

Carole Valentine

>Bob, if you have a flare you would just use a cone shape on the "ort" with no shoulder. In fact that's what I usually do, but there was a hairline crack on the neck of this piece and I wanted the support of the shoulder on the tenon. I have a rig similar to the one Greg mentions, but it is too big for things with less a 3/4" opening.

Re: Reverse chucking a hollow form

#5

Re: Reverse chucking a hollow form

Allen Neighbors

>Carole, thanks for posting this. That shoulder is a good way to do an HF that has a very thin top. I appreciate your sharing the idea.

I might turn some steps into my cone(Described, following) since I use a pretty standard size (5/8) opening on most forms.

Bob, I have a cone shaped gizmo, that fits in my chuck. It has a 3/8" hole through the center, with a long 3/8" rod that goes through it. There's a set screw (knob) in the largest diameter of the cone, that locks the rod into place. I have a piece of leather CAed to the end of the rod.

I put the rod all the way to the inside bottom of the piece, bring the piece up and fit the cone (foamy covered) into the opening and tighten the knob. Bring up the tailstock, and your contacts are the opening (cone), the inside bottom (rod), and the outside bottom (tailstock). It works pretty well.

Re: Reverse chucking a hollow form

#6

Re: Reverse chucking a hollow form

stacey s

>Thanks Carol. That is almost exactly how I reverse turn my hollow forms. Some times I use a cone shaped piece of wood other times I have the sholder like you do. Also I make sure to put some paper towels between the jam chuck and the vessel to make sure that I don't burn the wood incase it slips on the chuck.

Stacey

Re: Reverse chucking a hollow form

#7

Dick Hines

Re: Reverse chucking a hollow form

Dick Hines

>I use PVC step down or step up depending on how you look at them. 2"to 3", 4" to 5". There all kind os sizes. I upt a couple paper towels over the PVC and place the hollow form on the towels. Just bring up the tail stock and you are ready to go.

Re: Reverse chucking a hollow form

#8

How was it mounted when hollowing?

Jorge Castaneda

>I can see all the steps you said, but hollowing between points is not in my repertoire : )

Nice little thing

Thanks

Jorge

Re: Reverse chucking a hollow form

#9

Re: Dick, can you clarify

Allen Neighbors

>the step down/step up things for me? I'm slow, I guess. Don't know what you're talking about.

Thanks,

Re: Reverse chucking a hollow form

#10

Bob Moffett

Re: Dick, can you clarify

Bob Moffett

>The step down/step up fitting is a plumbing fitting (reducer) that is used to connect Schedule 40 4" PVC to 2" PVC and is avalable at either Lowes or Home Depot or any other place that sells plastic plumbing pipe. There are other sizes than the 4" to 2" that are avaliable. I just used that as an example. I made my vacuum chuck with a 4" coupler and have a 4" to 2" reducer and a 4" to 3" reducer that I can fit over it when I need a smaller size chuck.

Re: Reverse chucking a hollow form

#11

Leo Van Der Loo

here,s some more pieces that can help,

Leo Van Der Loo

>I also use the holding ways that Carole shows so well, and I have a few pieces in a pic. here that show other things that can be utilized, the small nibs are always used by the tail center, but when the opening is to large or out of round a rubber ball will conform to the shape of the opening, to hold the balls I have used the plastic pipes held in the chuck, than the ball and then the turning.

No good for rouging out, just take small cuts, and as always be careful.

Have fun and take care

Leo Van Der Loo


img

Re: Reverse chucking a hollow form

#12

Re: How was it mounted when hollowing?

Carole Valentine

>LOL! Jorge, you mean you have never hollowed between centers??? Why not? ;))

Seriously, I guess I did not make that clear! I put the 3" cube between centers and turned a shallow tenon, chucked it up, shaped it, hollowed it, then reversed it. If I was as brave as Jen was, I suppose I would have just parted it off without reversing it, but I don't like working that close to the chuck. If I had used a glue block, I could have parted it off without reversing it also, but I don't like to mess with glue blocks for some reason.

Re: Reverse chucking a hollow form

#13

Re: How was it mounted when hollowing?

Jorge Castaneda

>Carole,

I do mess with glue blocks for that very reason, they put the work away from the chuck and reverse mounting it is an option if you want to put details in the foot, if not you can just part it.

Thanks

Jorge

Re: Reverse chucking a hollow form

#14

Great Stuff! Thanks Carole and Leo!

Jennifer@Indy.USA

>

Re: Reverse chucking a hollow form

#15

Dick Hines

Re: Dick, can you clarify

Dick Hines

>Thanks for saving me having to explain the up-down thingies.