Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Future stupid questions

Posts

Future stupid questions

#1

Future stupid questions

Ron Hildreth, Alta, Iowa

>Hope you guys here on the turning board are prepared for all the dumb questions I'll be asking in the near future. BUT--you only have yourselves to blame! Through all your posts, I've became interested! I've been a regular on the woodworking board for a while, and been a woodworker for about 30 years, but never have done much turning. Out of boredom one day a few months ago, I decided to see what was up here on the turning board, and have been a lurker since. Intrique and curiosity has made me decide to try my hand at turning. Presently I have a home made midi lathe that's hard to find parts for, and has seen better days, so am looking at buying the Grizzly G1495 as a good "starter" lathe.

Soooo, be prewarned about anything I might dream up, as turning will be a relatively new adventure in woodworking for me, and I'm going to have lots of questions, I'm sure! Should be interesting!

Ron in Iowa

Re: Future stupid questions

#2

Re: Bring it on-we're familiar with....

Jamie Donaldson

>..converts to the addiction of turning! And remember,the only dumb question is the one you didn't ask!

Re: Future stupid questions

#3

Re: Future stupid questions

john lucas

>Ron I urge you to look at the Grizzley G0462. I think it's a better lathe and less expensive. It has a commons size spindle thread whereas the 1495 has 1"x12 which is an odd size.

You won't like the gap bed. It gets in the way more than it is useful. The headstock rotates on the 0462 which is much more useful.

You get a 2HP motor with the 0462 and only 3/4 with the 1495.

We are glad to have you on board and Jamie didn't say it but the only stupid questions are those not asked.

Re: Future stupid questions

#4

Re: Future stupid questions *LINK*

Bob Fawcett

>Look at the New Nova in the same price range as the Grizzly.

Better yet, get a Jet Mini. If your addiction takes like mine did, it won't be long before you want something else. If you decide turning is not for you a Jet mini is easy to sell and you didn't spend much anyway. This is the advice I got here about a year ago. Since purchasing the lathe my table saw, jointer, and planer are only used to make turning blanks and jigs.


Nova

Re: Future stupid questions

#5

Re: Future stupid questions

Chip in Plano

>Starting with a Mini is sound advice. No one suggested it but that's where I started. I turned eight 9.3/4" collection bowls for my church on my Jet Mini with only 1 month of playing around. 6 months later I upgraded to a bigger machine. My Jet Mini is now used for 1) Beall Buffing 2) spare lathe for the occasional friend that wants to stick of piece of steel in a spinning piece of wood 3) turning lids/spindles for bowls and collars for hollow forms 4) Occasionally, I even use it to sand pieces while I start another piece on my bigger lathe. I almost sold it but I'm glad I didn't.

Re: Future stupid questions

#6

Re: Future stupid questions

Carole Valentine

>Welcome Ron! And you cannot possibly have any more "stupid" questions than I did when I started turning 2 years ago! The best thing is, these fantastic people took the time to answer every single one of those questions. :) WC is where I learned to turn.

Re: Future stupid questions

#7

Re: Future stupid questions

Gary in Zirconia, NC

>I turned on a freinds 0462 and I would not wish this lathe on my worst enemy! What a piece of junk. Broken banjo, and tearing up a belt after one or two belts. (He went through several belts). He finally bought a PM 3520.

Re: Future stupid questions

#8

Sigh...another one down the slippery slope!

Molly Winton

>

Re: Future stupid questions

#9

Re: Future stupid questions

Jim Shaver Oakville, Ont.

>Welcome....

Becareful....if you turn a pen you'll be in big trouble.....

:-)

You can not just turn ONE..

Take care,

Jim

Re: Future stupid questions

#10

Re: Future stupid questions-Jim Shaver

Ron Hildreth, Alta, Iowa

>I've had conversations with you on the woodworking board! Glad to see you here, too!

Thanks for the advice on other lathes, but feel a bigger lathe would be more to my benefit, as I'm also a woodworking business owner, and have had to turn down jobs in the past for lack of a bigger lathe. The home-made midi I have now was handed down to me when my F-I-L pasted away a few years ago. I thought at the time I could fix up it's bad shape, but most of it is home made with j-rigged parts that are off only God knows where from. Found it would cost more than the thing is worth.

The Grizzly G1495 is one that I've used, owned by a friend of mine, and I've become familiar and comfortable with it, but might look at the 0462 a little closer. My basement shop isn't set up with any 220 circuits, so I'm pretty much stuck with staying in the 110v equipment, at least until I can rent or buy a bigger shop building hopefully this summer.

Ron in Iowa

Re: Future stupid questions

#11

Re: Future stupid questions

RevDoug

>Ron, I went with the Nove 1624. 16" swing, 1.5 hp, cast iron ways, headstock, tailstock, and banjo. I've already turned an unbalanced crotch piece that the lathe handled with no problems. Comes standard with 24" turnable didtance between centers and an unlimited number of bed extensions can be added. Not variable speed, but the 8 step pullies give a great speed range. In fact, I was concerned about the 214 bottom end. It is more than slow enough. Not sure that it's not really slower than advertized. Give it a good look.

Turn 'em round,