Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

First attempts

Posts

First attempts

#1

First attempts

Alfred Poor

>Thanks to all who chimed in to help with my new Jet mini lathe in December. The punchline is that the smoked leaked out of the windings after about 10 minutes of use, and they sent me a replacement motor. No problems since. I duplicated a meat pounder from the kitchen as some spindle work, then tried to learn to use my new chuck (never had one before). The first two bowls were "learning experiences" and not shown here. My next attempts were a bit more successful, but I still have a lot more to learn:



Cherry bowl, about 4" diameter



Osage orange bowl, 4.7" x 1.5"



Black walnut treasure box, 2" x 3.7"



Cherry top, 1.2" x 1.8"



White oak platter, 7.8" x 0.9"

All the wood came from trees on or near our property, except for the platter which was the cut-off of a rough cut plank, leftover from another project. Most pieces are finished with just butchers wax. I've still got a lot to learn about tearout and sanding and not leaving so many tool marks, but I'm having fun learning from my mistakes.

Re: First attempts

#2

Re: First attempts

Barry Turner

>My first attempts at turning didn't look nearly that nice. I like the rim treatment on the cherry bowl. You won't be seeing photos of my first bowl on here either.......:-)

Re: First attempts

#3

Re: First attempts

Carole Valentine

>Alfred, I would say you are off to a fantastic start, especially if you had never turned before you got that Jet mini in December! :)

Re: First attempts

#4

Barb Siddiqui

Re: First attempts

Barb Siddiqui

>Sweet! You're doing great. I'm new and having trouble learning to sand, too. Will post photos later. Just getting warm enough to work on it again around here. Those are nice first pieces. I'm impressed with your work.

Re: First attempts

#5

Re: First attempts

Joanne Adler in Pt. Pleasant, PA

>Hey! Welcome to posting on WoodCentral (yeah, I know--you posted back in December). I've told you before, this is one of the nicest groups of people you will find. And these turners are amazing! Geez, they even let us flatlanders lurk over here and ogle their work! You will learn a lot just viewing their posts. I'll save you some of the cedar I had to cut up. It'll go nicely with that new lathe.

Re: First attempts

#6

Re: First attempts

Alfred Poor

>I've done a little turning in the past, but not much. 30+ years ago, my wife gave me a Sears Companion (the brand below Craftsman) lathe that has spent most of its life being moved around the East Coast and ending up stored somewhere. I made a handful of wine stoppers a year ago, but that was about it. I tried a bowl using a turning plate this fall, but two pieces of the lathe broke, which precipitated the purchase of the Jet mini. So I'm not a total beginner, but close to it.

Thanks to all for the encouraging reactions to the photos.

Re: First attempts

#7

Re: First attempts

Jennifer@Indy.USA

>Alfred, these a wonderful first attempts. I think you really have a knack for the lathe.

Keep them coming!

Jen

Re: First attempts

#8

Re: First attempts *LINK*

Bob Fawcett

>Albert,

Looks great to me. I am new to this as well.

My sanding really improved after I purchased a cheap right angle drill from Harbor Freight and started power sanding on the lathe with Vince's disks.


Blue disks

Re: First attempts

#9

Re: First attempts

Ron in Drums PA

>They pretty darn good Alfred.

I like the platter the best!

Re: First attempts

#10

Re: First attempts

Jeff Myroup

>I think these are very good. I like the Cherry bowl, and the Oak plater the best. I like the detail on the plater. As for the sanding and tear out those will come with time. You are off to a good start.

Jeff

Re: First attempts

#11

Re: First attempts

Alfred Poor

>Thanks for the sanding tip; I'll have to give it a try. I've found that I like the foam sanding pads from Harbor Freight; they don't get too hot and they conform well to curved surfaces.

Re: First attempts

#12

Some very nice first attempts....

Jake Niedling

>Alfred - you are doing very well, keep up the good work.