Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Chucks - how many is enough??

Posts

Chucks - how many is enough??

#1

Chucks - how many is enough??

Chip in Plano

>So how many do you have?

I don't have enough chucks or I have too many blanks primed for spinning or is this just an advanced sympton of this addiction. I've got extra jaws but I always seem to have the chuck bases taken with the multiple projects I'm working on. I like my Nova Midi but I really tend to use my SuperNova almost exclusively. I like the heft plus I like the bigger expansion. Part of my problem is that I hate dismounting and remounting pieces just to free up a chuck. The inevitable wobble is aggrevating dispute how minute it can be.

Wish I had some cheese & crackers to go with my whine.

Re: Chucks - how many is enough??

#2

Never enough

Mike Cunningham (Cape May NJ)

>I have three, two Axinisters and a Nova. I'd love to have a chuck for every set of jaws.

Re: Chucks - how many is enough??

#3

Re: Chucks - how many is enough??

David Walser

>I agree. I find I want two chucks to finish turn a box. If, for whatever reason, I want to start another turning before the box is finished -- I need more chucks!

For this reason, I think I'm going to be using faceplates with glue blocks a lot more in the future. Faceplates are a lot cheaper than are chucks.

Re: Chucks - how many is enough??

#4

How High Is "Up?" |;-}}}}} [2]

Mark Mandell - Gone Round In Jersey

>

Re: Chucks - how many is enough??

#5

Re: Sounds like you just need........

Jamie Donaldson

>... to finish some more of those works in progress!

Re: Chucks - how many is enough??

#6

How many clamps are enough?? :))

gil jones

>

Re: Chucks - how many is enough??

#7

How Many Blondes Does It Take To------

Ken Oakley-Sunny St. Cloud, Fla.

>

Re: Chucks - how many is enough??

#8

Re: Chucks - how many is enough??

Bill Grumbine (Kutztown PA)

>Chip, I see you are getting some of the usual answers here, so I will try to help you out some. I got along for years with one chuck. Then, luxury of luxuries, I acquired a second one! I discovered I "needed" it. Time has passed, and while I doubt I will ever be in the company of those who have one chuck for each set of jaws, I have one Stronghold, with another body in the mail right now, two Talons, a Barracuda II, a Barracuda IV, and the wee little Barracuda whatever. Part of my justification for all these chucks is the number of students I have on my three different lathes on a regular basis, but I know people who never have anyone in their shop besides themselves who have way more chucks than I do.

Like Jamie says, if you find yourself out of chucks because they are holding work, maybe you need to get some time in the shop to finish some things. At the least, you could sell them to make money for more chucks! :)

Bill

Re: Chucks - how many is enough??

#9

Re: Chucks - how many is enough??

Allen Neighbors

>Chip, I was thinking along these same lines this morning. I have two SuperNova2s, and have three sets of jaws, plus the Cole jaws. I'm like you, in that I hate to dismount something just to use the chuck for another project.

I'm really thinking about getting some of those faceplate rings; but I think that I can get some for the SN2 Chucks.

Do you know what I'm talking about? I can't find any on the Teknatool Webpages... the link doesn't open. They are surely cheaper than another chuck, and with enough of them you could have any number of pieces in the works.

Re: Chucks - how many is enough??

#10

Re: Chucks - how many is enough??

Bob Fawcett

>Another possibility, get a tap the size of your spindle and you can make wooden faceplates and other helpful items. It may not replace the need for another chuck, but it can be real useful. Shoot you could even tap your work and mount it direct :-)

Re: Chucks - how many is enough??

#11

Re: Found them, Chip

Allen Neighbors

>This is from the bottom of page 29 in the Teknatool Catalog (A pdf file that I downloaded):

FACEPLATE RINGS

� Stock Code: 6000, 6001, 6002

� Strong and fast mounting method for bowl blanks. A better alternative to the woodworm screw which is only suitable for smaller bowls.

� Offers the secure mounting of a faceplate with the quick convenience and power of a chuck. Strong mounting and method even with irregular sized wood and rough cut surfaces.

� Three Sizes:

- 50mm (2�) (fits standard 50mm jaws), Faceplate diameter (3�)

- 100mm (4�) (fits 100mm jaws), Faceplate diameter (5�)

- 130mm (5�) (fits 130mm jaws), Faceplate diameter 6.25�

Re: Chucks - how many is enough??

#12

Re: A tap for my Oneway spindle

Allen Neighbors

>is probably more expensive than the faceplate rings... :o)

Re: Chucks - how many is enough??

#13

Dick Hines

Re: Sounds like you just need........

Dick Hines

>I have found that 4 works for me. I started with a Nova and 4 sets of jaws. I got tired changinf jaws every time I wanted to do some thing different. 4 chucks and 4 sets of jaws. Just right , for now. Oops forgot about the one on my Jet mimi lathe.

Re: Chucks - how many is enough??

#14

Re: Chucks - how many is enough??

Carole Valentine

>I have 2 SuperNova2s, one Nova Midi and a collet chuck. I really want another SN2 body. I hate changing jaws, but there is one advantage to having to change them - I always blow out the chuck body and clean any gunk off before I mount a different set of jaws. If I never had to change jaws, I probably wouldn't do that, at least not as often. I also have one of those Teknatool faceplates that mounts in the Supernova2. I like it but I just keep forgetting I have it!

Re: Chucks - how many is enough??

#15

Re: Chucks - how many is enough??

john lucas

>I have 4 chucks right now. 2 Vicmarcs, one grizzly vicmarc copy and one older nova tommy bar chuck. I am planning to sell the older Nova chuck and get another vicmarc. I have a ton of faceplates. I made them from nuts and washers. That way I can mount my vacuum chucks permanently on it's own faceplate.

I find that wood moves a little so if you take it out of the chuck and leave it any time at all it will move, so I just plan on that and true it up. If you leave wood in your chuck for any length of time you risk rusting the chuck jaws. Especially woods like Oak.

Re: Chucks - how many is enough??

#16

Richard Allen

Re: Chucks - how many is enough??

Richard Allen

>Dick Sing has three Vicmarc lathes. He claimed the three lathes kept him from having to swap out chucks. I am fairly sure he was joking.

Re: Chucks - how many is enough??

#17

Is $26.95 too expensive?  *LINK*

Peter Teubel

>


33mm tap from Beall Tools

Re: Chucks - how many is enough??

#18

Re: Chucks - how many is enough??

C.W.Stivison

>Well I bought chuck today and I thought I was on top of the world, but after reading this I guess I have a long way to go.

CW

Re: Chucks - how many is enough??

#19

I g for that, Bob. I can have as many as twenty o

Don Henthorn

>or more with glue blocks attached and never have to remove a piece from the chuck until it is finished. For my way of working it is just superior to scroll chucks most of the time. When I absolutely need a scroll chuck, I have one. But that ain't often.

Re: Chucks - how many is enough??

#20

Re: That's good. Thanks, Peter.

Allen Neighbors

>

Re: Chucks - how many is enough??

#21

Re: You will always need ONE more than you have

Russ Fairfield

>

Re: Chucks - how many is enough??

#22

Re: Chucks - how many is enough??

Steve Russell

>Hello Chip, from a fellow Texan!

I'm a professional bowl turner and I have a total of 10 chucks currently... 6 Vicmarcs, 3 Super Novas and 1 Nova. Each has a different set of jaws on it. Yes, I'm too lazy to swap them out! Been there, done that - for five years and got the T-shirt to prove it. I looked at the time I was spending swapping jaws back and forth and decided it was cheaper to just get more chucks. :-)

In a production studio, time is money. You have to do everything possible to save time on non-income producing tasks, thereby allowing more time for production. Production = $. Simple concept really. It works for me but I'm not done yet. I plan to get 4 more Vicmarcs this year for a total of 10 Vicmarcs, plus the 4 Novas.

That many chucks may sound like a lot of chucks for a one man shop, but they pay for themselves very quickly. Plus, it's just a lot more convenient when you do not have to break your rhythm when you're turning. :-) When you're in the "zone", it's sweet and you don't want to do anything but turn, turn, turn.

Most hobbyists can get by with one, maybe two chucks but that just is not practical for me. Good luck to you and best wishes in all of your woodturning endeavors!

Steve Russell

Eurowood Werks Woodturning Studio

The Woodlands, Texas

Machinery, Tool and Product Testing for The Woodworking and Woodturning Industries

Re: Chucks - how many is enough??

#23

Is This A Trick Question ? ? ?

Barry Turner

>Is this a trick question? One can never have enough chucks.

Just like one can never have enough guns, pocket knives, bowl gouges or whatever else man happens to fancy at the moment. Just like men can never be rich enough and women never thin enough.

Go buy yourself another chuck. It's apparent that you are at least one short of what you actually need. I recommend a Super Nova II. You'll feel better for it. If you don't, go buy another.

Re: Chucks - how many is enough??

#24

Re:Shopping Plans...It's settled..

Chip in Plano

>Now here is a man with sound advice. I will certainly give myself permission to buy at least one more chuck. I have all you guys to validate (to the LOML) that 2 just isn't enough. 4 seems to be a good number. I think I'll buy number 3 on Monday since Woodcraft is 1 mile from the office and I do have a gift certificate burning a hole in workbench. I've got an anniversary next month that'll be a good time from #4. The birthday in May and Fathers Day in June should be good for the captive hollowing system I'm looking for. After a day of hollowing free-hand, my hands are pre-arthritic so it's a medically sound decision. I know I have an entire forum of friends to support these needs....not wants.