Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Bevel protractor *LINK*

Posts

Bevel protractor *LINK*

#1

Bevel protractor *LINK*

john lucas

>I admit it, I suffer from never make the same thing twice disease. Because of this if have to change my saw a lot to cut the different angles. This means there are a lot of test cuts to get the angle correct. I've bought a lot of different gadgets over the years to try and help this but they never have the correct angle, or just flat out don't work.

When I was at Highland Hardware they had a close out on a Starret Bevel angle Protractor. I never would have bought it at the normal price but it was more than half off so I got it. What a great tool. I'm still in the early stages of finding out how well this thing works as a set up tool but so far it's great. I could not find this on Starret's web page but found something very similar in the Enco catalog. There are also some models that are quite a bit more expensive and may be a little more accurate but for woodworking I think the less expensive model will work.

My first tests were to tilt the saw to 22 1/2 degrees and rip some wood. This has always been one of the harder things for me to do because I don't have a high qualitys saw or blade. I was only off a hair and that was a with a board that hadn't been planed and trued up. It was close enought than some thick veneer inbetween each piece would take up the slack.

My next test will be a compound miter. These have always been a pain because you have 2 variables, the miter gauge and the tilt of the blade. Should be interesting. I'll take the time to true up this next board.

Anyway, I think this is going to be a really good tool and not that expensive.


http://www.use-enco.com/CGI/INSRIT?PMAKA=635-6601

Re: Bevel protractor *LINK*

#2

Bevel protractor detail

john lucas

>This shows a detail of the face. It reads to 1/12 of a degree. The left arm is adjustable which is really handy for setting up the table saw. I wish it had a shorter replaceable arm for setting the scroll saw but I should be able to make some wooden angle gauges for this purpose using this tool as an accuracy check.


img

Re: Bevel protractor *LINK*

#3

Re: Bevel protractor

Norm Smith in Nova Scotia

>John, that appears to be a great aid for segment turning, plus all of the other frustrating angle cuts. Love to hear how you get along in the next goaround.

I remember you talking about trying to find an accurate 90 degree flute bit. Did you ever find one?

Norm

Re: Bevel protractor *LINK*

#4

Re: Bevel protractor

Bill Youngblood

>Hi John, I use a protractor that I got from Beall Tool Co. It is extremely accurate, measuring the piece rather than setting the blade of any particular saw. It is a few dollars more but in the same price range. I have only had it for a few months and so far it has worked out great.

Bill

Re: Bevel protractor *LINK*

#5

Re: Bevel protractor *LINK*

Bill Youngblood

>You can see this protractor at the link below. Click on the 'Products' button in the upper left corner.


http://www.bealltool.com

Re: Bevel protractor *LINK*

#6

Re: Bevel protractor *LINK*

Stuart Johnson

>I use one of these and find it very accurate and easy to use. At 2" square it will fit just about every where.


img

Wixey Angel Gauge

Re: Bevel protractor *LINK*

#7

Re: Bevel protractor

john lucas

>Norm I need to contact the various companies about the bits because each time I've checked bits by a particular brand, some will be exactly 90 and some will be a little off. So far CMT and Bosch have had the most that checked out to be exactly 90. All of the CMT's that I checked (5) were dead on. Be aware that my sample base is really small so It may or may not be indicative of any particular brand.

Re: Bevel protractor *LINK*

#8

Still another option

David Walser

>I haven't used this, but it came up as I was searching on Amazon. Definitely lower cost. Not sure about how well it might work for segmented turnings.

7" True Angle

Re: Bevel protractor *LINK*

#9

Re: Still another option

john lucas

>David That's what got the whole thing started. I went to Highland Hardware to buy one of the angle gauges that looks like the one you posted but better quality. It was more expensive than I though (about $30) and then they put the starret on the 1/2 off table so I got that instead. The one thing that concerned me was the rounded corner was too large so you would have a very small straight area in contact with the blade which would ruin your accuracy.

Re: Bevel protractor *LINK*

#10

Re: Bevel protractor

IAN

>I've been using the wixey for a couple of months now and have also really like the results. it will work on just about any saw in my shop.

IAN