Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

problem solved

Posts

problem solved

#1

problem solved

Bill Youngblood

>Thanks for all the suggestions on my 'bleeding' problem. As promised, here is the finished piece. There was a small amount of red dust in the Holly. I applied boiled linseed oil, mistake number two. The oil turned on the red dust like a neon sign. I remounted it on a faceplate with a glue block and cleaned off the oil as much as possible with a cabinet scraper. The piece is only 1/8" thick so I didn't have much to work with. Unfortunately, the oil went quite deep so it is still a little yellow; but I went ahead and finished it anyway just for the experience.

I gave it a light coat of clear lacquer and sanded with 180. Another coat of lacquer and sand with 220 and so on up to 400. I then gave it several coats with light 400 sanding between coats. I finally polished it with automotive rubbing compound.

It certainly is not gallery quality but a fabulous learning opportunity.

To all you lurkers out there, if you have a problem don't hesitate to ask about it. These are the greatest and most sharing people in the world.

Thanks again for all the suggestions.

Bill


img

Re: problem solved

#2

Re: problem solved

Greg Haugen

>Outstanding Piece Bill!! Very nice form. I like the "twist." I like it because the "detail" involves the whole piece. My eye is drawn all the way up and back down. I think sometimes other segmented work have "dead" areas on the vessels. Not that there are bad but rather they don't have as much "detail" than other areas.

Very Nice!

Greg

Re: problem solved

#3

Re: problem solved

Mike Cunningham (Cape May NJ)

>Very nice Bill......"Staircase to Heaven"?

Re: problem solved

#4

Re: problem solved

Bill Youngblood

>Thanks Mike. I referred to it as the project from hell.

Re: problem solved

#5

Re: problem solved

Mike Cunningham (Cape May NJ)

>Well then that's pretty much where that staircase leads!! ;^)

I've had numerous projects with that name!

Mike

Re: problem solved

#6

Brad Vietje

NICE !!! Looks like Gallery fare to me...

Brad Vietje

>

Re: problem solved

#7

Thanks Greg

Bill Youngblood

>

Re: problem solved

#8

Nice!!!

Ron in Drums PA

>

Re: problem solved

#9

Re: problem solved

Jennifer@Indy.USA

>Hi Bill,

This is a very nice piece. I like the way the segments wind their way up the form. Love the added touch of the black rim that brings everything together too. While I personally have never attempted a segmented piece, due to the fact that I don't have near the patience it must take, I totally respect the time, planning and effort that goes into them.

Bravo!

Jennifer

Re: problem solved

#10

Thank you ... Thank you very much

Bill Youngblood

>

Re: problem solved

#11

Re: problem solved

john lucas

>I can see why you wanted to save that one. It was a lot of work and well worth saving. You done good as we say here in the appalachian mountains. I would be quite proud of that piece.

You also did a pretty darn good job taking the photo. The only thing I'd do differently is to try to move the backround a little further back if possible. You might also try moving the light just a little higher but aim it back down so the lower half doesn't get dark. That will make the shadow on the right a little shorter.

Re: problem solved

#12

Re: problem solved

KEN RIEDEL

>the guys will check that out Tuesday

Re: problem solved

#13

Re: problem solved

Carole Valentine

>Really nice piece, Bill. Seems to me that Holly wants to grab anything within 6 feet if there is a chance of staining! I really admire the patience and preciseness of segmented turners. I would never make the cut! Is there any problem with using lacquer over BLO? How long did the BLO dry?

Re: problem solved

#14

Thanks Carole

Bill Youngblood

>This was my first time with Holly. I don't think I will use it again to this extent. Like you say, it is a magnet for anything that will stain it. So far the lacquer is holding; but it's only been a few days. I took off as much of the oiled surface as I could before re-finishing.

Generally, I wouldn't put a non-oil finish over oil. Time will tell. Most of my work is BLO and then polished with the Beall system. I have to admit that I do like the lacquer finish. I will probably try it again.

Re: problem solved

#15

Great Save

Bill Stehman

>Great save

and well worth the effort Bill. Nice shape and excellent joints as evident with the holly. If joints aren't perfect dark lines will show. Well done on a difficult piece.

Bill