Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Box Elder color

Posts

Box Elder color

#1

Box Elder color

Troy German

>I'm new to turning and found this site only recently. It's been like finding a treasure chest! I've been swimming in new, practical, excellent advise for about two weeks now. So, first I want to say thanks to everyone for your questions, responses, and pics of work posted here. It's been terrific to learn from.

Now, on to my question: I turned a vase out of Box Elder and finished it with tung oil and Beal buff. The block that it came from is sealed (with Anchor Seal I believe) on all sides. The block is very yellow, but the finished vase is creamy white. Does Box Elder yellow with age or did the sealant tint the block?

Thanks in advance,

Troy

Note: I�ve included a picture of the vase (5"w x 9"h) and the other half of the block it came from. I know that the quality is poor, and there is great advice on how to improve that in other posts. That�s a skill I�ll be working on soon, but today this will have to do. Comments on the form, however, would be greatly appreciated.


img

Re: Box Elder color

#2

Re: Box Elder color

Mike Schwing from Md.

>All wood darkens and/or yellows with exposure and time. Tung oil is also very yellow and will impart that yellow color to anything it touches.

Freshly exposed box elder is normally very bright and creamy, and stays that way for longer than some other woods, but suffers the same disposition in the end - it yellows.

Lacquers tend to have the least color in them of most commonly used wood finishes, but they're not always the easiest to use. A "finish" coating on a workpiece should be applied to protect and enhance that piece. If it can't do both, sometimes it is better idea to apply none.

Very few woodturners can resist the impulse to apply some sort of finish.

Re: Box Elder color

#3

Re: Box Elder color

Carole Valentine

>Hi Troy. I usually use a two part bleach on Box Elder (and some other light woods like holly). It whitens the light wood while not affecting the red streaks. You can then finish with a clear water based finish (which doesn't yellow as much) or, if you have sanded finely enough, just buff and wax. Any oil will darken the wood but unfortunately, so will time. The red will also eventually turn brown if exposed to light.

Re: Box Elder color

#4

Re: Box Elder color

Troy German

>Thanks. Actually, I like the yellow and was hoping it would return.

Re: Box Elder color

#5

Re: Box Elder color

Bill Neddow

>Carole gave the perfect answer for keeping Box Elder light in color. But if you want it to go yellow, simply use a oil based finish. A linseed oil finish goes yellow a little faster than a tung oil based finish.

Re: Box Elder color

#6

Re: Box Elder color

Troy German

>Thanks. I found a post on two part bleaching and might try that for a different piece from this block. How will that effect the spalt lines?

Re: Box Elder color

#7

Re: Box Elder color

Carole Valentine

>Troy, I honestly can't remember how it affects spalt lines. It seems to me that it doesn't. Try it on some scrap. I use two applications of the bleach. Read the inside of the box for additional tips.

Re: Box Elder color

#8

Re: Box Elder color

Brodie Brickey

>Troy,

Although your current piece isn't a wealth of flame, it is nicely proportioned. If you get a piece with a lot of flame in it and want to preserve the color you will need to use a finish with a UV blocker in it. Exposure to sunlight will take most of the color out of box elder.

Regards,

Brodie

Re: Box Elder color

#9

Re: Box Elder color

Troy German

>Thanks. If I shop for more Box Elder I'll look for some with more red in it.