Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Finally! I managed to not let...

Posts

Finally! I managed to not let...

#1

Finally! I managed to not let...

Pat Taylor

>...this piece fly off the chuck! Everything else I've chucked has let loose at some point in the turning process. I guess I'm finally getting the hang of doing tenons correctly. This is maple, turned wet, warped like hell, but has a nice grain pattern from being near a crotch.

I have a rough-turned bowl from the same piece that really shows the crotch pattern, so I'll post that when I finish it.

Critiques welcome, but I suspect there's not much to say because it's an awfully boring piece! I guess you can tell me to let it dry first before I finish it. :)


img

Re: Finally! I managed to not let...

#2

This angle shows the warping

Pat Taylor

>By the way, the size is 5.5" diam.


img

Re: Finally! I managed to not let...

#3

Re: Finally! I managed to not let...

Carole Valentine

>Pat, from looking at "busted knuckles" on your blog, it appears that you are trying to grip a bowl blank by grabbing about 1/2" of a long smooth tenon in the chuck. You need try to cut a nice flat shoulder for the chuck jaws to fit against. If your jaws are dovetailed, like the Nova jaws, you need to match that profile on the tenon. I think you will find that you have much less of a problem with pieces coming loose and the blank will run truer (is that a word?) as well. Keep up the good work. Your enthusiasm is refreshing. :)

Re: Finally! I managed to not let...

#4

Re: Finally! I managed to not let...

Pat Taylor

>You're absolutely right. My more recent chuck/tenon attempts have used a nice shoulder and a dovetail, with much better results.

The long smooth tenon you saw actually had a grove I was trying to use, as Raffan does in his "Turning Bowls" book when gripping a finished foot, but my results were a bit off from his! ;)

Thanks!

Re: Finally! I managed to not let...

#5

Re: Finally! I managed to not let...

Bill Hale / Woodspinner

>Another consideration is if the wood is a little soft I run a bead of thin ca along the bottom of the tennon. After it has set I do a little clean up of the tennon and then use it. Almost never lose one.

Bill in Casa Grande, AZ.

Re: Finally! I managed to not let...

#6

Re: Finally! I managed to not let...

D Putland

>Hi

Get a chuck with the oneway style of jaws and you will find that run away bowls will be scarcer then hens teeth.

Denis

PS: I do not sell them , just have a couple of there chucks:):)

Re: Finally! I managed to not let...

#7

Re: Finally! I managed to not let...

Allen Neighbors

>Carole's right, your enthusiam is refreshing. Nice work. Glad you kept it spinning ON the lathe. :o)

How does one find your blog?

After all those previous posts about warping, I decided to try it with some of that sweet gum I have. I put a large crotch bowl blank on the outboard end, turned it round and cut a tenon, and found an inclusion that ran through the center of it, edge to edge. Being such a masterful sort, I decided that it wouldn't stop me. I mounted it in the chuck, inboard, installed the bowl steady, and duct taped the rim with two full wraps of 2" duct tape.

I turned about 2 1/2" deep, about 1/4" thick, and decided I needed to sharpen my gouge. Turned aside to hit the off switch, and jammed the gouge into the rim. It came apart. So much for the duct tape and the masterful attitude!!! :o)

I'll try again tomorrow... different blank...

Keep after it, Pat... let us see some more. How much sanding did you do on this before it warped like that? Is it dry now?

Stay safe......er, than me... :o)

Re: Finally! I managed to not let...

#8

Re: Finally! I managed to not let... *LINK*

Pat Taylor

>See the link below for the blog.

The dish is dry now, and looks about the same as in the photo. During finishing, I sanded 60, 180, 240, and then from 1500 to 12000 in about 10 steps (with a sanding kit, I forgot the brand). The cherry, maple, and beech have really taken the high-grit sanding well.

Thanks for the encouragement. I've had a few catches-while-looking-the-wrong-direction too. Very dissapointing. I've broken a few after being forced to turn too thin after a few of those catches.

The worst was when I accidentally tried to change the speed on my jet mini (by moving the belt) before it was all the way stopped. The tip of my index finger went between the belt and pulley. OUCH! That's made it difficult to type for a few days. I'll spare you the pictures.


http://www.beadsandcoves.com

Re: Finally! I managed to not let...

#9

Leo Van Der Loo

Allen I have one that's going to be a challenge to

Leo Van Der Loo

>sand, this center cut from a Elm crotch is 20" wide and 18.5" long, it did a good twist, and it is dry now, so now I will be like riding the roller coaster sanding this, whenever I will feel up to it, that is going to be fun I think.

Have fun and take care

Leo Van Der Loo


img

Re: Finally! I managed to not let...

#10

Leo Van Der Loo

Re: This angle shows the warping

Leo Van Der Loo

>Hi Pat I remember my first trials turning bowls, but didn't have a place to go and ask "how to do,s", so your lucky there, but you still have to do it yourself, keep going back for more and not giving up is the only way, after the initial trials you will get better, so don't give up, and try different ways, it is really fun turning wood.

I have had more luck holding forms like the bowl with a recess rather than a tenon, but I do use both, just depends on the shape and wood, anyway you're doing good, keep at it.

Have fun and take care

leo Van Der Loo