Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

WHEW!!!

Posts

Re: WHEW!!!

#26

Keith Tompkins

Re: WHEW!!!

keith tompkins

>Wow! Thanks everyone....I'll try to reply to all at once..The piece is 12" tall. I removed the base (a bit of trepidation though) because it interrupted the flow I was looking to achieve. While I'm no Tilman Riemenschneider, I enjoy the challenge of this type of carving....lots of design op's here..Rather than a realistic appearance, I wanted a "suggestion" of fabric. My off-center tailstock is nothing more than a "plug", turned to fit the opening in the vessel. I simply mount the vessel between centers after hollowing, then move the point of the tailstock about 1/2" off center in the plug. By rotating the plug in the turning , I can remove wood from the outside of the turning in small increments....I end up with thin walls on most of the turning, leaving a heavy spot to carve on one side. A needle scaler works well for larger areas, but for details, NG. So, I took a worn-out 1/8" carbide cutter, and removed the cutting end. Rounded the end over, and inserted into a wood handle. Tap, tap, tap with a small hammer to produce the texture. Thanks for the kind words...Now,I hope the "big guy" likes my pieces as much.!

Re: WHEW!!!

#27

Re: WHEW!!!

Jennifer@Indy.USA

>Keith,

This is fantastic!

I absolutely love it!

Jen

Re: WHEW!!!

#29

Absolutely suberb Keith!

Molly Winton

>

Re: WHEW!!!

#30

Cool, Your BEST work yet! Outstanding!

Doug Thompson near Cleveland

>

Re: WHEW!!!

#31

Mike Stafford

Re: WHEW!!!

Mike Stafford

>Wow, that is a beautiful piece. You did a wonderful job carving the linen folds. Very lovely!!

Re: WHEW!!!

#32

Re: WHEW!!!

George Van

>Even with all the comments I still have to say �Fantastic Keith�.

Re: WHEW!!!

#33

Re: WHEW!!!

Mike Rubes, Apex, NC

>Hi Keith,

Really outstanding piece! It looks like a ruffled sheet! I love that effect.

Thanks for the pic!

Mike

Still aiming for the bar in Apex, NC

Re: WHEW!!!

#34

Very well done!!

Bernie

>

Re: WHEW!!!

#35

Re: WHEW!!!

John Lucas

>Keith Beautiful piece and the carving is well done. Good job on the photo as well.

To save you allthe Tap,tap,tap, buy a dremel engraver and install the rounded over 1/8" bit. It produces a different pattern than the single tap method but you might find it useful. It's much more forgiving and controllable than the needle scaler.

Re: WHEW!!!

#36

Re: WHEW!!!

Don O.

>Another amazing piece Keith! Great photo too.

Re: WHEW!!!

#37

Re: WHEW!!!

Fred Bearman

>Once again I am amazed at the talent and vision within this group - I am not a particular fan of carving on turning, but this piece is just beautiful and somehow just begs to be touched, and even in the picture conveys the soft flow of fabric. Very nice!

Fred Bearman

Port Huron, Michigan

Re: WHEW!!!

#38

A good concept

keith zimmerman, Normal, IL

>I really like your concept and execution Keith.

keithz

Re: WHEW!!!

#39

Keith Tompkins

Re: Bravo

keith tompkins

>HI Steve, Yeah, I spent some time carving this, but much of the time the lathe was used to hold the piece...does that count?

Actually, the carving took an evening....it's the SANDING that's a killer!

Re: WHEW!!!

#40

Keith Tompkins

Re: WHEW!!!

keith tompkins

>Uh-OH!!!! While I appreciate the kind comments, all this talk of "execution" has me a bit worried!! LOL