Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Cherry Burl Bowl

Posts

Cherry Burl Bowl

#1

Cherry Burl Bowl

Bill MacLachlan

>I only seem take pictures of my turings when they collect. Finally got around to taking some. After yesterday's discussions thought I should finally post some of my stuff.

This is a cherry burl bowl. Size = 3.5 x4.

Critiques wanted.

Thanks, Bill


img

Re: Cherry Burl Bowl

#2

Re: Cherry Burl Bowl

Mike Nelson

>Bill, You should post your work more often, nice piece with a very good finish. Since you ask for critiques, you might want to "lose the sheet" as Jamie would say and use light poster board to better draw attention to the work. Jamie must be out somewhere confiscating cameras and blue table clothes or he would have commented. ;)

Re: Cherry Burl Bowl

#3

Re: Cherry Burl Bowl

Bob Fawcett

>Mike,

"light poster board" does this refer to the currugated stuff they make signs out of?

Where do you buy this stuff?

Thanks

Re: Cherry Burl Bowl

#4

Re: Cherry Burl Bowl

Bob Fawcett

>WOW Bill, you have been busy, both turning and photographing. Some nice turnings and better photos than I can manage so far.

Re: Cherry Burl Bowl

#5

Keith Tompkins

Re: Cherry Burl Bowl

keith tompkins

>HI Bill, Here is my critique for what it's worth. Your piece is quite nice to look at, but a couple of changes would make an improvement. First, the curve from the rim to the foot is not a smooth continuous curve...it's got an abrupt change just below center. That causes the viewer's eye to focus there. Second, the chuck (I'm assuming you are using a chuck) has dictated the size or the foot, making the chuck a design consideration. A smaller foot would do two things..first, it would allow more room to continue the curve, which would help create a flow from top the bottom, and it also creates a sense of lift. The bigger foot acts to anchor the form to the surface which it rests on....giving a heavy appearance.

Re: Cherry Burl Bowl

#6

Re: Cherry Burl Bowl

Bill MacLachlan

>Keith;

I understand what you are saying concerning the foot, but how do you make that design "modification" if the wood is only so thick? You still need to grab hold. I have noticed the chuck does determine many of my foot sizes and I am trying to work that out.

Thanks all for the commensts.

Re: Cherry Burl Bowl

#7

Re: Cherry Burl Bowl

Bill MacLachlan

>I am interested in the "light poster board" as well. I assume this is not the stuff we used use in school?

I know the sheet sucks, and I have tried other material but got comments that it was too "blue".

Re: Cherry Burl Bowl

#8

Re: OK Bill, no blue comments.....

Jamie Donaldson

>... needed here! I suggest you find a photo spot with a wall behind-I hang a white vinyl window shade (on a pull down roller)for a wrinkle free backdrop, easily rolled up for out of the way storage and cheap! It would help show some of the bowl interior as well as the profile if you raised the camera to a slightly higher angle.

Re: Cherry Burl Bowl

#9

Re: I suggest you reverse the hollowed .....

Jamie Donaldson

>.....bowl on a jam chuck, held in the chuck jaws and tailstock against the base. Then you have easy access to the base and can make it any size you wish.

Re: Cherry Burl Bowl

#10

Keith Tompkins

Re: Cherry Burl Bowl

keith tompkins

>Hey Bill, some of this will come with experience....if you turn the inside with a flat bottom, you're stuck with it. With some practice, you'll turn the outside as far as you can, and then measure the inside depth. Reverse the bowl to gain access to the base, then finish turn the bottom, checking the thickness as you go. No more chuck problem!

Re: Cherry Burl Bowl

#11

Re: Michaels or Hobby Lobby...

Allen Neighbors

>Just ask for "foam core". You can also get it at photo shops. It's lightweight, and you can get it with foil on one side... I think... not to sure about that.