Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Any reviews of the new Grizzly?

Posts

Any reviews of the new Grizzly?

#1

Any reviews of the new Grizzly?

Mike Cunningham (Cape May NJ)

>A friend is in the market for a new lathe and is seriously considering the Jet 1642. That said, we noticed an ad for the new Grizzly of the same dimensions that appears quite similar. I have several Grizzly tools, most notably the 17" bandsaw and while I'm pleased with them I know that their lathes are suspect. Does anyone have any info on this latest machine?

Thanks,

Mike

Re: Any reviews of the new Grizzly?

#2

Re: Any reviews of the new Grizzly?

Allen Neighbors

>Don't know if it's the one you're interested in, but a friend of mine is going to purchase the GO462 16X43 Grizzly next month. He's been turning on my Old Griz (GO579)and likes it enough to want one.

I hope they have done something about insuring the headstock and tailstock line up after turning the headstock to the side and back.

Re: Any reviews of the new Grizzly?

#3

Re: Any reviews of the new Grizzly?

Ralph

>Tough, I don't think the first one has shipped yet

Re: Any reviews of the new Grizzly?

#4

Andy DiPietro

Sounds Dangerous, 600 rpm min @ 2HP

Andy DiPietro

>Sorry guy's, safety first. At 600 rpm min speed you better start with a well trimmed blank or the lathe will rock and roll over. Unless you like hospital food I would buy a better lathe like the Jet if you want to do 16" bowls or hollow forms. It would be fine for spindles and small bowls, but then you would not need 2 hp for that.

I started out with the Grizzly G1495 which was good for pens and small bowls. I had it bolted to the floor and the tail section was anchored to my concrete basement wall. It had a min speed of 500 rpm and I could rock the head section if the blank was not trimmed well.

I now own a Powermatic 3520B and I can vary the speed down to 50 RPM and use the full 2hp on a poorly trimmed large blank safely. Just something to think about.

Andy D.

Re: Any reviews of the new Grizzly?

#5

what spec are you reading....

Ralph

>Try

# Speed range, high: 0-3200 RPM low: 0-1200 RPM

Re: Any reviews of the new Grizzly?

#6

Andy DiPietro

Re: Grizzly G0642, Grizzly.com

Andy DiPietro

>This spec was copied from there website and it is the model Allen talked about. Your #'s are for the G0632.

G0462 Wood Lathe With Digital Readout

Motor: 2 HP, 110V, single-phase

Swing over bed: 16"

Distance between centers: 43"

Heavy-duty, precision ground cast iron bed and cast iron legs ensures stability and minimal vibration

1" x 8 TPI RH headstock spindle

Spindle tachometer with digital read out

MT #2 spindle & tailstock tapers

Spindle bore: 3/8"

Outboard turning is easy with standard tool rest extension

10 speeds: 600 - 2400 RPM

The G0632 has a min speed of zero or there abouts so that would be safe. It looks like a copy of the Jet 16x42.

Andy D.

Re: Any reviews of the new Grizzly?

#7

You're right Ralph

Mike Cunningham (Cape May NJ)

>That's the model that I referred to when I started this thread. I suppose it's too new for a review.

Thanks,

Mike

Re: Any reviews of the new Grizzly?

#8

Re: You're right, too, Andy.

Allen Neighbors

>You and I were talking about the same one. Now that you've pointed out that very important point, I'm going to have a talk with my friend about it.

Thanks for bringing that to my attention.

Re: Any reviews of the new Grizzly?

#9

He was asking about the G0632

Ralph

>So posting the spec for the other lathe is not accurate.

Re: Any reviews of the new Grizzly?

#10

Andy DiPietro

Re: He was asking about the G0632

Andy DiPietro

>Sorry, you are correct. I should have posted under Allens posting. But I think some good has come from this. Now Allen can talk to his friend about the G042.

For the record I have other Grizzly equipment that I really like.

Andy D.