WE MOVED...
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

boxwood and mahagony platter

Posts

boxwood and mahagony platter

#1

boxwood and mahagony platter

John Lucas

>This platter was done using the router table jig for my lathe. I move the table up 1/2" above center, then below center 1/2" and then on center. This gave an angle to the 3 v grooves. I'm not sure I like the way the ends distort where the beads are. It didn't dawn on me at the time that because they are at an angle they won't look exactly like the one in the middle. Next attempt will be to use a different router bit for the two outside inserts. This will give them a radically different shape.

The texture was applied using a Dremel engraver with a rounded over tip.


img

Re: boxwood and mahagony platter

#2

mahagony and Inlace mirror

John Lucas

>This was a mirror I started while doing an Inlace demo for our club. I needed some bead practice with the skew so I turned the handle with beads. Got a minor catch while doing the left handed side of the 3rd bead so I reduced the size of that one and the two beside it cover up. hey I never said I was perfect, and that's why I needed to practice my beads.

This is Black Inlace with the turquoise plastic chips.


img

Re: boxwood and mahagony platter

#3

new ornaments

John Lucas

>I needed to fill up my case with new ornaments so I started turning some more. I also needed to have some pieces to show using the routed insert process so these filled a double bill. The dots on the one near the right were drilled and then a piece of a dowel was inserted. Then it was turned to a cylinder and routed using the index wheel for precise stops.


img

Re: boxwood and mahagony platter

#4

Brad Vietje

3 Great Posts, John -- Very Nice !!!

Brad Vietje

>

Re: boxwood and mahagony platter

#5

Re: 3 Great Posts, John -- Very Nice !!!

Norm Smith in Nova Scotia

>John , I like the way the platter looks with the inserts the way that they are. Man , the ornaments are real nice.

Norm

Re: boxwood and mahagony platter

#6

Steven Antonucci

Of the three, I like ornament #2 and the platter..

Steve Antonucci

>best.

I thought at one point you were going to show us a lot more of the router inlay? I only count 12 pieces. Surely you can index more than that ;-)

FYI- I see beer taps when I look at the inlays in the platter. Am I the only one?

Steve

Re: boxwood and mahagony platter

#7

Re: new ornaments

WHH

>John,

Do you hollow your ornaments?

thanks

Re: boxwood and mahagony platter

#8

Re: new ornaments

john lucas

>I hollow my 3 part ornaments and my 2 part ornaments. Sometimes I get a little anal about the hollowing so my ornaments are really light. Heavy woods are hollowed even thinner, often down to 1/8" or less to keep them light. I've gotten fast enough that it doesn't slow me down much and customers seem to really like the light feel.

Re: boxwood and mahagony platter

#9

Andy DiPietro

Re: new ornaments

Andy DiPietro

>Beautiful work as always John. How do you get such a tight fit on the mahogany inlay? Do you joint the small mahogany pieces before gluing them in the routed groove? Are you using a 45 deg router bit in the Dremel?

Andy D.

Re: boxwood and mahagony platter

#10

Re: new ornaments

John Lucas

>Andy Tight fit is easy as long as you route the groove straight. I use a 90 degree v groove bit but beware, many 90 degree bits arent'90 degrees. Check them when you get them and send them back if they are less than 90 which most have been.