WE MOVED...
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Motor/controller question *LINK*

Posts

Motor/controller question *LINK*

#1

Motor/controller question *LINK*

Mike Cunningham (Cape May NJ)

>I just added a third lathe to my shop, a 1971 Rockwell/Delta 46201 with Reeves drive. I'd like to convert this to a Variable speed and reverse. Would someone with knowledge of such things please check the link and advise if the controller depicted will satisfactorily operate a 3/4 HP for this type setup. If not, what kind of controller do I need and will any 3/4 HP motor work or does it need to be specific to variable speed control? Could I use a controller with the existing OE motor?

I'd like to avoid, if possible, the $400 route of a Leeson controller and motor such as that offered by CS.

Thanks

Mike


VS Control

Re: Motor/controller question *LINK*

#2

Re: Motor/controller question *LINK*

Gary Ratajczak

>Mike:

The controller you have linked to is for a DC motor. My guess is the motor you have now is AC - so this unit would not work.

But.......

I have purchased the same controller you show, along with a 1/2HP DC motor for my Jet mini - not yet hooked up, but the motor and controller work GREAT.

As DC motors loos torque at low speeds, you generally spec something a little larger than required. I have posted a link to a motor ar Surplus center that would work, and for the right $$. You would need the controller you show, along with the fuses and resistors (also from Surplus Center) to match the motor HP and voltage. You can just call Surplus Center to help you out.

The motor I link to has a face frame mount. You can use some large band clamps, or pick up a mount at a local motor shop.

To vary an AC motor, you would need a Frequency Drive. I have not used a setup like that, but believe the above will be less cost.

NOTE - Check E-Bay - I bought my 1/2HP Leeson brand new in the box for low $$. I bought the same controller, new in a box for $60.00.

Good Luck!!


http://www.surpluscenter.com/item.asp?UID=2007011615440302&catname=electric&qty=1&item=10-2213

Re: Motor/controller question *LINK*

#3

Re: Motor/controller question

Mike Cunningham (Cape May NJ)

>Gary,

Thank you, exactly the info that I'm looking for with a link as well!

Mike

Re: Motor/controller question *LINK*

#4

Re: Motor/controller question

Russ Babbitt Jr.

>You do not say if the motor is AC or DC. If it is the motor that came with the lathe it is most likely AC. If so the controller will not work. The controller will drive a DC motor. If you plan on keeping the reeves drive I do not know if it would be reversible. I would be inclined to replace the reeves drive with a set of step pulleys, if possible. Then replace the motor with a DC motor with the linked controller.

Re: Motor/controller question *LINK*

#5

Re: Motor/controller question

Randy Privett

>Mike,

One of my lathes is the same one, but when I got it, the Reeves Drive was missing. It had the 3/4 HP motor with a 3ph electric. I bought this one and attached a remote, and its still going after three years. The price has gone up a little from when I bought it, but it works great.

http://cgi.ebay.com/HITACHI-Inverter-VFD-1-5-HP-230V-1-or-3_W0QQitemZ7604099359QQihZ017QQcategoryZ78192QQcmdZViewItem

Randy

Re: Motor/controller question *LINK*

#6

Re: Motor/controller question

Mike Cunningham (Cape May NJ)

>Thanks Randy, I'll check it out. I assume you used this with the 3/4 hp that was in the lathe, correct?

Re: Motor/controller question *LINK*

#7

Re: Motor/controller question

Randy Privett

>Yes, that lathe has a 3/4 hp.

Randy