Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

sharpening a Glaser gouge on a Tormek

Posts

sharpening a Glaser gouge on a Tormek

#1

sharpening a Glaser gouge on a Tormek

eliot d

>Sometimes I use a grinding wheel with the Wolverine jig to sharpen tools, and sometimes I use a Tormek. For most of my HSS tools the Tormek, while slower, definitely produces a sharper edge. I say 'most' because for some weird reason, I can't seem to get my Glaser gouge sharp on the Tormek. I have the proper Tormek jig and use exactly the same set up for another gouge as for the Glaser. This HSS gouge is truly sharp. But the Glaser just doesn't get sharp on the Tormek.I can sharpen it just fine on the wheel. I can only guess that it has something to do with the type of steel. Has anyone experienced difficulty sharpening a Glaser gouge on the Tormek?

Perplexed in sharpening land.

Re: sharpening a Glaser gouge on a Tormek

#2

Re: sharpening a Glaser gouge on a Tormek

Allen Montgomery

>I don't have a Glaser gouge but I do have a Glaser/Lacer skew. The "blade" is a Glaser and Alan Lacer turned the handle with a stainless steel ferrule with the tool having his grind, of course. I do have a Tormek and use it religiously for my spindle tools except this skew. Because of the grind mostly. I know I have sharpened my G/L skew and no problems. Other times I sharpen it, hone it, check for glint and its sharp. In the matter of a few cuts it changes how its cutting and I check for glint again and there are timy spots across the surface. Almost like chips. That wasn't there a minute or two earlier. I have heard that the harder steels are more brittle. I don't know if that's my issue or what is. As far the Tormek. I don't know. I have never put that in the jig and sharpened it.

I know at one time CET (parent company for Glaser) was going to put out a "diamond" grinding wheel for the tools. I do everything and anything in my power not to support that company though. In talking with a "Name" turner and finding out about legal battles and what CET has done to him after he left. I will not support CET. I also know Mike Mahoney, who uses "luxury" steels alot, says he can't get the higher end steels as sharp as M2. The Diamond Wheel would solve that, I believe is the thinking.

There is a trade off for a "edge holding capability" if its too hard to get it there???

It's a tough situation and I know I'm not much help.

A.M.

Re: sharpening a Glaser gouge on a Tormek

#3

Re: sharpening a Glaser gouge on a Tormek

john lucas

>Eliot I'm kinda guessing but since the Glaser tools are pretty hard it simply may take longer to grind away enough metal to reach a sharp edge. The argument that the PM tools don't get as sharp as HSS is possibly the same thing.

My skew is HSS and gets absolutely razor sharp if I take the time to do it. It's pretty easy to get sharp enough to shave hairs. I think it gets every bit as sharp as my High Carbon steel skew. It does take more patience to do it.

The Tormek wheel is quite fine and it would take a while to grind an edge that has a slight round over at the tip. Anyway that's my guess. You'll probably get a lot of responses on this so it will be interesting to watch.

Re: sharpening a Glaser gouge on a Tormek

#4

V-15 Glaser gouge on Tormek, no problem

Dave Smith, Longview, WA

>

Re: sharpening a Glaser gouge on a Tormek

#5

A norton SG/3x wheel would be your best bet

Devon Palmer

>I have a glaser V15 (that I rarely use anymore because it just WON'T get that sharp and is inefficient IMHO) and the only way I can get even a marginally acceptable edge is with a Norton 3x wheel or a diamond hone. Supposedly, regular ALOX wheels can't maintain enough sharpness to cut the hard metal effectively, therefore, they fracture the cutting edge on a VERY small scale, leaving a broken surface thats not very sharp.

You could probably get there with a tormek, but, it'd take a month of Sundays.

- Devon Palmer, Columbus Ohio

Re: sharpening a Glaser gouge on a Tormek

#6

.. Let me clarify a "month of Sundays" LOL

Devon Palmer

>Before I get flamed *G*

For me, sharpening a bowl gouge is a 6 second operation with the grinder running right next to my lathe. I start it when enter the shop and shut it off when I leave. I use the Oneway Mastercut M4 PM gouge which I'll sharpen probably 4 times when doing a 16 inch maple bowl. Since its SO sharp, I can take a heavy cut without much load on me or the lathe. It takes me a good 30% longer with a comparable glaser becuase I can't remove as much wood (otherwise, I'll grind my powermatic 3520A to a stop). I more than make up the extra 30 seconds of sharpening time with the increase in productivity. The A11 seems to be a much better balance of performance/edge maintainability/sharpness than the V15, but, probably not as good as the M4 for what I do. Your results may vary :)

Anywho, I'm a somewhat agressive, production-turner wannabe, so that works for me. No doubt a tormek would give a better edge, but, would take a lot longer than 6 seconds.

Re: sharpening a Glaser gouge on a Tormek

#7

Re: .. Let me clarify a "month of Sundays" LOL

eliot d

>You , apparently, are having similar difficulties. This is very disturbing because, after all, Glaser gouges are considered excellent; and one pays more for them. I'm not sure which Glaser I have; the handle is maroon. I'm not worried about time spent sharpening; otherwise I would not use a Tormek at all. My problem is that , even with much time sharpening it on the Tormek, it just doesn't get really sharp -- like my "regular" HSS gouge of exactly the same geometry. I have a Glaser skew chisel, too, which I have not tried to sharpen on the Tormek; so now I'm worried that I'll have problems with it too. Perhaps I 'll see what the Tormek people have to say about all this.

Re: sharpening a Glaser gouge on a Tormek

#8

glaser tool grinding tips

Joe Sanders

>I own several glaser gouges and skew chisels. I have never had a problem sharpening them on the Norton wheel or on the Tormek.

From what I understand and researched, they are made of A11 Crucible Powder Metal and their ability to hold an edge is unsurpassed. For those who were able to attend the AAW event in Louisville, CET had the President of Technology of Crucible talking about the 10V material. I personally learned alot. That is why they are superior to any other metal available today. Of course, if you want good stuff you pay more.

I have attached a link to an article Jerry Glaser wrote awhile ago for everybody to refer to.

http://www.woodcentral.com/articles/turning/articles_132.shtml

Also, it is a good idea to read about the steel itself on the www.glaserhitec.com website. I noticed they have posted a "killer V" section that talks about the materials.

I hope it helps everybody.

Just keep on turning!

Re: sharpening a Glaser gouge on a Tormek

#9

Is it for sale?

Dave Peebles Lyons, Ohio!

>Devon,

If this is one of the older Glaser gouges.. Before the new owners took over, I would be interested in buying it.

If you would like to sell it, shoot me an email.

I have not had the problems with my Glasers that you mentioned.

Best wishes,

Dave