Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

How to process this hunk of wood

Posts

How to process this hunk of wood

#1

Steve Kubien

How to process this hunk of wood

Steve Kubien

>Evening everybody,

Whilst visiting my semi-local tree dump I came across a branch about 8" in diameter which is bent at a tight 90� angle. Standing up it looks like a capital "L". Each arm is just shy of 24" long. I'm not sure what wood it is (pine/spruce I think) but the shape grabbed me so home it came. Now, what to do with it...

I've only got a mini lathe and 10" diameter is as big as I can go. Do I cut the arms off, leaving a vee shaped chunk and turn a bowl, knowing that the pith will remain in parts? Do I cut off the arms and slab it, removing the pith, and go for a plate of some sort? No matter what species it is, I think there should be some neat grain inside. I really don't want to mess it up if I can avoid it.

Thanks for your insights.

Steve Kubien

Ajax, Ontario

P.S. Finished my first bowl about a week ago! I'll post a pic for your amusement when I find where my daughter hid it (she really liked it).

Re: How to process this hunk of wood

#2

Re: How to process this hunk of wood

Tom Libby

>Might be an opportunity for trying an angel wing bowl, as in http://www.aroundthewoods.com/wings.shtml

It's a great site.

Good luck

Re: How to process this hunk of wood

#3

Re: How to process this hunk of wood

David Breth

>I'd vote for #2. Hack the arms, then slab the middle and get the pith out of there. Lowest risk (as far as I know) to losing the piece during the dry time. Leave some room at the ends (greater than your 10" diameter) to allow for some loss at the edges.

Something else you can do is slab it, then turn one piece green and dry the other. Might be able to do the wing-bowl thing and let it warp into something pretty slick, for example.

David B.

Re: How to process this hunk of wood

#4

Steven Antonucci

Sometimes, wood is better unturned...

Steve Antonucci

>from how you describe it, I'd split it in half along the length and resaw it into 2 L shaped "cants". Then I'd probably leave it to dry for a while and try to figure out what to do with the book matched slabs. Maybe a base for a table. Maybe some small cabinet doors.

You could always turn it later into some winged bowls if you wanted to.

Steve

Re: How to process this hunk of wood

#5

Re: How to process this hunk of wood

Sam Dean

>Hi Steve,

When I find pieces of wood like that, I like to do a natural edge with wings, so you end up with 4 "bullseyes" where the pith goes through. Just turn it really thin and sand by hand after it dries.

Thanks,

Sam


img

Re: How to process this hunk of wood

#6

Re: How to process this hunk of wood

TDRice

>I agree with Sam but you might put the bottom of the bowl at the outside of the curve giving you an extremely winged piece.

Re: How to process this hunk of wood

#7

Brad Vietje

In Either Case...

Brad Vietje

>This is a cool opportunity to play. If you are not (yet) a natural-edge bowl maker, you can make things that don't involve the bark edge.

In any event, this is wood that will very likely move a lot, so I'd suggest turning something quite thin, wet sanding, and letting it move as mother nature dictates.

Safe spinning,

Brad Vietje

Newbury, VT

Re: How to process this hunk of wood

#8

Re: How to process this hunk of wood

Colin Spencer

>Steve

This is what I did with a similar shaped piece of Olive.

Colin


img

Re: How to process this hunk of wood

#9

Thanks everybody

Steven Kubien

>I really appreciate all of the ideas. Colin, that bowl is fantastic! Several steps (and leaps and bounds) beyond my skills but dfeinately something to shoot for. For the next week or so I am just going to seal the ends and mull this over (although I am leaning toward turning it really thin while its still green and watching it distort).

Cheers,

Steve Kubien

Ajax, Ontario