Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

OK, now it is war - a bit lengthy

Posts

OK, now it is war - a bit lengthy

#1

OK, now it is war - a bit lengthy

David Breth

>Last night I started working on a large piece of osage orange - my first O O. The wood had different ideas.

First, I got a screw stuck in there when putting the faceplate on. It stopped dead with maybe an inch still to go. It was so stuck that I couldn't back it out with my power drill or a screw driver. Vice grips snapped the head of the screw off. I complimented the wood on its density, and said "well, that was unexpected!" or something along those lines. Then I spent about a half hour drilling, gouging, grabbing, pushing, making lewd suggestions and ultimately getting the screw out of there.

Then I thought I'd better pre-drill the holes for the faceplate screws. Good thinking (I'm not sure I've ever had to do that). So, the drill bit got stuck. Hopelessly stuck. Drill couldn't hold it tight enough. Had to flip the blank upside down with the bit end held in a vice, then spin the bowl off of it. This was probably another twenty minutes of fun.

Then I pre-drilled the holes for the faceplate a bit more wisely - about a quarter inch at a time before cleaning the bit and going back for more. No more faceplate screw problems.

It was time to mount up. This blank was round-ish, as I had used the bandsaw to knock the corners off, but still had some bam bam. It was during one such bam bam that - and it happened too quickly for me to tell you for sure what happened, but I think the tool popped off the rest, got smacked by the wood on the next revolution, and smacked me pretty convincingly on the knuckle where the index finger meets the hand. It stung a little, and I couldn't help but think that the battle had been fairly joined. Fighting back, eh? OK, now its ON.

It took a while to get the wood round, but it got easier and easier. Still, the wood is in the concrete family, and I was sharpening approximately every revolution of the wood. Got the bottom done last night, and sanded it down. Generally, I start out with paste wax, spend a lot of time with the first grit and things go quickly from there. It took three "treatments" of paste wax to get the tool marks/high areas out - testimony to my great toolwoork, but also testimony to the hardness of this wood.

When I left it last night, it was chucked up and ready to turn out the inside. Haven't looked at it yet, but I'm pretty sure that some defense mechanism will have grown on the wood overnight.

Now, I'm not going to deny that all of the above problems are my own fault, but I'm still pretty sure that either this piece of wood or the wood gods in general have it in for me on this one. But the piece will yield. I will prevail. You are going down my friend, down like the lead duck that you undeniably are.

I can tell you this much - if I ever do a craft show, and put this bowl on the table, I'm going to stick about a humongous price tag on it just to compensate for my war wounds.

It does have some pretty nice figuring by the way!

David B.

Re: OK, now it is war - a bit lengthy

#2

Re: I laughed for ten minutes

Allen Neighbors

>at this post. David, I've been there... through every step!... and I can sympathize with you. And I'm still laughing. That post was funny!

You didn't say, but I'd be willing to bet that the OO was either cured, or pretty close to cured dry. When it is, it's as bad or worse than Pecancrete.

Hang in there, Friend, and keep sharpening... you might want to get another gouge on order, lest you be without when the tool's finally ground away. :o)

Dampen the outside somewhat, with heavily soaped water, while you're turning the inside... allow it to dry as you finish the inside bottom. It'll help to keep the cracks down.

Blessings... perseverance... tenacity....

Re: OK, now it is war - a bit lengthy

#3

Re: OK, now it is war - a bit lengthy

TDRice

>O. O. is my favorite wood but it can be a bit hard. I try to cut it in the winter while the sap is down and turn it wet. I finish turn it wet and have never had any noticable distortion.


img

Re: OK, now it is war - a bit lengthy

#4

Re: OK, now it is war - a bit lengthy

TDRice

>O. O. is my favorite wood but it can be a bit hard. I try to cut it in the winter while the sap is down and turn it wet. I finish turn it wet and have never had any noticable distortion.

Re: OK, now it is war - a bit lengthy

#5

Re: I laughed for ten minutes

adrien

>The Melanesians make boats by placing hot coals on the wood, then scraping the burnt stuff off.

Just a suggestion for the inside of the bowl.....

Re: OK, now it is war - a bit lengthy

#6

Re: OK, now it is war - a bit lengthy

Jeff

>Your post made me laugh. I have a oo blank on my lathe right now. This was my first attempt with oo and I thought it was me and my technique. I have been turning for about 5 yrs with no instruction and today went and signed up for a intro to bowl turning class. Good luck - I hope to hollow mine tomorrow.

Re: OK, now it is war - a bit lengthy

#7

Re: I laughed for ten minutes

David Breth

>That might have been easier than using my bowl gouge and then giving up in favor of the round nose scraper. The bowl gougle took me in reasonably until I couldn't catch bevel anymore. The inside was not as difficult as the outside, but still VERY unforgiving with respect to tool work. I was much more careful than I was on the outside to avoid leaving tool marks.

Sanding was still brutal. Sandpaper was shot after about two seconds in contact with that stuff. Put one coat of deft on inside and out, and I have to say, I think I might actually win this one - although it would not surprise me if this bowl went for its own little version of detante, and cracks itself apart. "If I can't be an intact log, then you can't have me as a bowl."

David B.

Re: OK, now it is war - a bit lengthy

#8

Dick Hines

Re: OK, now it is war - a bit lengthy

Dick Hines

>I had a piece of O. O. a few years that had been in a barn for years.

I decided to give to a turner I did like much.