Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Spindle work

Posts

Spindle work

#1

Spindle work

Ken Grunke from SW WI

>This is what I've been up to lately...

Jim Cox, a member of our AAW chapter who runs an established cabinetmaking/high end crafts business was overloaded with work before Christmas and asked me to take over this spindle turning job for him--183 spindles total, for a balcony railing and stairway in a former church building being remodeled as a private dwelling.

These were pre-turned to rough stage by Jim on a homeowner-quality Delta duplicator machine attached to his lathe, and then passed on to me for the detail and finishing with hand tools. They are paint-grade spindles, sanded to just 120 grit and by no means perfectly matched to each other which might be apparent upon close examination of the photo.

This job has been an enjoyable challenge for me--I've done small batches of spindle multiples in the past, but none in this amount. Biggest challenge was working without any type of steady rest aside from my left hand, wrapped around the spindle as it guided the skew chisel along the long, straight section.

These were all turned from poplar, 1 3/4" square in lengths from 24" to 38". I still have about 50 to do--some 34's, 15 of the 36's and 22 38's. Here's just 8 of the 34" ones:


img

Re: Spindle work

#2

Brad Vietje

Re: Spindle work

Brad Vietje

>Looks great, Ken. I've never taken on a larger production run like that, but I bet its a great learning experience -- especially if your job is to add the fine details after a duplicator rough-in. Good to see some spindle work posted here, too.

Safe spinning,

Brad Vietje

Newbury, VT

Re: Spindle work

#3

Very Nice!

Greg Haugen

>

Re: Spindle work

#4

Re: Spindle work

Duane Hill

>Good job Ken. Nice work there. I do the same with my left hand.

Re: Spindle work

#5

Re: Spindle work

John Lucas

>Ken I've done a lot of spindles but never anywhere near that many at one setting. You get the endurance award for that.

Re: Spindle work

#6

Re: Spindle work

Ken Grunke from SW WI

>John, there's no way I could have done even half of them in one setting LOL! These were done over the course of a week, and I still have 50 to go.

Re: Spindle work

#7

Re: Spindle work

John Lucas

>I would think so. About how many per hour did you average.

Re: Spindle work

#8

Re: Spindle work - to clarify

Ken Grunke from SW WI

>geez, I wish we could edit our posts here...

There's only a couple hours of work in the picture, but all I've done so far, about 130, have taken approximately one week and only 3-5 hours at the most in a day's time so the job has been spread out enough to not overload my middle-aging 53-year-old body.

Sorry to disappoint all my fans out there, *ahem* *cough* but I'm not a Super Spindle Turning Maniac. ;-))

Re: Spindle work

#9

Re: Spindle work - to clarify

Barry Irby

>There is a guy in our local turning club that worked for a lumber yard that has a shop. They often got him to reproduce dozens of spindles similar to these. A master of the skew. He demoed some made of Western Red Cedar about the same diameter, but about two feet long. He commented 7 minutes a spindle, start to finish. Amazing to watch.

Re: Spindle work

#10

Re: Spindle work - to clarify

Ken Grunke from SW WI

>I'd be thrilled to see someone turn a 24" spindle that fast, starting from square the full length. My spindles were all pre-turned to rough size, about 1/16" over and I thought I was fast to be able to do one in 10 minutes.