Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Ellsworth Gouge

Posts

Ellsworth Gouge

#1

Ellsworth Gouge

Jim

>For several months, I use the Ellsworth Signature gouge for almost everything. It works for me. However, I'm struggling to keep it sharp with the original profile. I use the Ellsworth jig with a Kelton system set up 7" from the wheel face and 3-4 inches below center. I'm following the set up instructions to the letter. I have a six inch grinder. The wings are swept back almost 1-1/4 inches now. The instructions suggest 3/4". Anyone having a similar issue?

Thanks, Jim

Re: Ellsworth Gouge

#2

Re: Ellsworth Gouge

Gary in Zirconia, NC

>Just don't spend as much time grinding the sides. It'll shorten up.

Re: Ellsworth Gouge

#3

Been there, done that...

Peter Teubel

>Mine got so long that I chopped it off with an abrasive saw and started over. I found the problem was that I rolled the tool over too much during the sharpening process *AND* spent too much time on the sides. One has to watch the shape with each trip to the grinder and correct every few grindings. Spend more time on the center and less on the sides. Don't go too far on the side....even if it means you don't get the whole side edge. It'll come back into place.

To correct what you have, just grind the center back alot...like to 1/2". It will look kinda funky, but once that's done, THEN sweep the whole edge and even it up.

Re: Ellsworth Gouge

#4

Re: Ellsworth Gouge *LINK*

Bob Fawcett

>Jim,

I realize you have different jigs, but this may help. The link is to Oneway's videos for using their system.

Once you have restored your gouge to the profile you want, sharpening requires very little metal removal. Use a sharpy to color the bevel before you start and only remove enought metal to take away the color. This can also show you if your setup is a little off. Make sure the distance from the front of your jig to the end of your tool is exactly the same each time you grind.

Look on the left and find the "Tool Grinds Library" for a reference to what the tool should look like.


Video

Re: Ellsworth Gouge

#5

Re: Ellsworth Gouge

John Lucas

>Personally I love a long wing on the side. My favorite gouge is ground this way.

Re: Ellsworth Gouge

#6

RE: Ellsworth Gouge

Jim

>Thanks everyone!

I e-mailed David Ellsworth.

He said the same thing...

Less time on sides...more time on nose.

Light fingertip pressure...

Re: Ellsworth Gouge

#7

Thanks everyone!

Jim

>Thanks everyone!

I e-mailed David Ellsworth.

He said the same thing...

Less time on sides...more time on nose.

Light fingertip pressure...

Re: Ellsworth Gouge

#8

Re: Ellsworth Gouge

Bill B

>Just to reinforce what everybody has said, an important thing to rememeber about this or any other grinding jig is that the jig only controls the angle that the tool is presented to the grinding wheel. The shape (meaning how pointed or blunt the nose is and how long the wings are on the sides are under your control and the jig can't keep you from making the sides longer or shorter than the "ideal" size.

Bill

Re: Ellsworth Gouge

#9

Keith Tompkins

Re: Ellsworth Gouge

Keith Tompkins

>Jim, keep in mind the length of the side grind is not as critical as the ANGLE of the side grind. Steep sides cause catches...see the article in the latest AAW American Woodturner for a photo of that.The side grind should appear to curve inward.

I wouldn't bother grinding the tool shorter...a 1/2" is a lot of material. Just focus on grinding the tip as you sharpen,until you're happy with the length; the long grind won't bother anything. Like JOhn Lucas, I prefer the long side grind ...for hollowing.

Re: Ellsworth Gouge

#10

Re: Ellsworth Gouge

Jorge Castaneda

>Hi Gary,

I love my Ellsworth gouge too and have a 6" grinder like you do, I had to shorten the protruding about 3/8 to get back close to the original look of the grind, it was an improvement but then I was turning in a friend's shop and his grinder is an 8", voila! back to the original shape.

I'll be getting a new grinder very soon.

By the way I use the Ellsworth jig.

Jorge

Re: Ellsworth Gouge

#11

Sorry Jim!

Jorge Castaneda

>

Re: Ellsworth Gouge

#12

Re: Ellsworth Gouge

Barry Irby

>My all time favorite tool.

I went to a turning demo where ten of us were turning. I took my own gouge but used some else's grinder. (We shared it) By the end of the second day my faovrite gouge was losing its favored status. The shape ahd changed just enough to make it "catchey". I was really glad to get it back home and whip it into shape.

I would work on improving my grinding technique and bear down a bit on the nose and leaves the wing lightly touched for a while and the shape will come back. Do check your set up.

I really wish I have measured the length of mine when I bought it. I am very happy that after years of use I see no real loss of length, but I would like to know for sure. Day to day sharpening seems to take of a few thousandths. You should get hundreds of sharpeings per inch. I would not grind away that valuable steel just to do it.

Re: Ellsworth Gouge

#13

Re: Ellsworth Gouge

Jorge Castaneda

>Barry,

Yes mine got catchy too, very pointed, too agresive; when I did round the tip some there was some improvement; I did not complete my sentence when I said I shortened the overhang, I meant when setting the jig, instead of protruding 2", I set it to protrude only 1 5/8" it took about a year little by little to completely earase the bad shape, still not perfect, the wings have a hump that when I did use an 8" grinder went away.