Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

cutting moderately -sized logs on the band saw

Posts

cutting moderately -sized logs on the band saw

#1

cutting moderately -sized logs on the band saw

eliot d

>What's the best way to cut -- say an eight inch diameter -- log on a band saw. I'm talking about cutting it to length. Obviously, the blade wants to grab and rotate the log. I'm not happy with the sled idea because they never seem to fit on the table with enough room. I suppose I should just go outside and use the chain saw. Any other thoughts? I'm posting because I keep ruining blades!

Re: cutting moderately -sized logs on the band saw

#2

Re: cutting moderately -sized logs on the band saw

bob davis

>i crosscut logs regularly using a sled with appx 4" high back,actually i have two,one for up to 6

' dia another for larger logs, learned this the hard way after mangling a few blades

Re: cutting moderately -sized logs on the band saw

#3

Timberwolf AS 3/8" x 3tpi blade & sled

Dominic Greco in Richboro PA

>Eliot,

Funny you should mention this now. I just got finished cutting an 7" dia. apple log on my band saw. I just cut right down the middle, centered on the pith. This is done free hand without using a fence.

I then flatten this cut face with my jointer. But you could also use a scrub plane to get it reasonably flat. Then I use place the flat section against the bandsaw fence and saw off the pith. From then it's an east matter to saw up slabs.

If you try to saw a wet log with a resaw blade, you may find that it will bind up and often catch. I found that using a AS 3/8"x 3 TPI Timberwolf blade from Suffolk Machinery really helps when sawing up "wet" wood. This blade is made for cutting wet wood and features specially set teeth to clear the sawdust. If you call Suffolk, ask to talk to a tech and they will steer you in the right directions. They are very helpful.

When the log is prone to rolling, or too big to handle comfortably, I use a simple down and dirty sled. The design came from somewhere in the FWW archives. It's just a (2) 5" wide x 18" long pieces of 3/4" plywood that have been assembled into an "L" (so you get a 5"x5"x18" long angle). A couple of 2" tall gussets at either end help support the fence. Simple lay your log on a flat surface, and place the fence along side. Use some 1 1/2" (or there abouts) long machine screws to temporarily fasten the log to your fence. Now bring this over to the bandsaw and cut the log along the pith like above. The rest is as I described above.

Good luck!

See ya around,

Dominic

Re: cutting moderately -sized logs on the band saw

#4

Keith Tompkins

Re: cutting moderately -sized logs on the band saw

Keith Tompkins

>Hey Eliot, I think unless you have a sled, as well as an assistant, the chainsaw option is actually safer, and faster. Those ruined blade are trying to tell you something...be careful, as the operation you are attempting can be dangerous.

Re: cutting moderately -sized logs on the band saw

#5

Re: cutting moderately -sized logs on the band saw

eliot d

>Thanks to all for advice and safety concerns.

Re: cutting moderately -sized logs on the band saw

#6

Re: cutting moderately -sized logs on the band saw

john lucas

>I agree with Keith. without a custom made sled and probably an extension table for the bandsaw this is an extremely dangerous thing to do. Even with a chainsaw ripping logs can be tricky.

Re: cutting moderately -sized logs on the band saw

#7

Re: cutting moderately -sized logs on the band saw

Ken Grunke from SW WI

>I've ruined or damaged more than a couple blades by doing this, it's always a scary thing. If I really had to do it again freehand, without a cradle/sled that is, a wedge-shaped piece of scrap wood under the leading side of the log works pretty good to retard it's rotation--and feed it into the blade very slowly. A wedge on the trailing side might not be a bad idea, either.

The last time I had a catch, it was quite violent and I felt lucky that the chunk of wood missed my face! Other times, the blade became tightly embedded in the wood making it extremely difficult to remove.

Guess I'm saying that some type of cradle or sled is crucial in this operation, otherwise you're gambling away either your blade, the wood, or possibly your good looks!

A simple V-shaped cradle of plywood, with screws strategically placed to bite into the wood is something I'll be putting together. My bandsaw doesn't have a miter slot, but I think using the cradle freehand should work fine.

Re: cutting moderately -sized logs on the band saw

#8

Re: cutting moderately -sized logs on the band saw

john lucas

>ken I find an L shaped cradle for the log works better for me. I put big screws into the log in several places. I can make thick or thin slices this way. Of course a V shaped cradle worked well for cutting a log in half. The L shaped lets me cut on both sides of the heart or I can make platter blanks.

Re: cutting moderately -sized logs on the band saw

#9

Re: cutting moderately -sized logs on the band saw

Carole Valentine

>I agree with the chainsaw advocates. The first and last time I tried to do this on a bandsaw with a dogwood limb, it was a truly frightening experience. I am lucky I only lost my blade and not my fingers. I was stupid enough to think I could hold the limb and prevent it from rolling. NOT! I do use my chop saw on small straight limbs.

Re: cutting moderately -sized logs on the band saw

#10

Re: cutting moderately -sized logs on the band saw

Barry Craven

>Hello everyone,on page 64 of the American Woodturner (AAW'S) mag

last issue Winter 2006 Volume 21,#4 is a good saftey stand for chainsawing. hope this helps

Re: cutting moderately -sized logs on the band saw

#11

Re: cutting moderately -sized logs on the band saw

Frank of Mantua NJ

>I have cut cedar and Soft maple up to four foot long with a sled and a 1/2" 3 tpi blaid. Its a simple job but, It is a hand full I have roller stands on bouth sides.

Re: cutting moderately -sized logs on the band saw

#12

Re: cutting moderately -sized logs on the band saw

Bruce Forrest

>Get yourself an electric chainsaw and do it indoors. How many ruined bandsaw blades equal the price of a cheap electric saw?

Re: cutting moderately -sized logs on the band saw

#13

I never use the bandsaw for that...

Brian Hahn in SW Wisconsin

>It is way to dangerous and way to easy to ruin a blade. Normally I'll take it out to the shed and use my electric chainsaw. (Quicker, easier and quieter than a gas saw.) Or I'll cut it with a hand saw.

But the one thing I won't do is cut it with the bandsaw.

Re: cutting moderately -sized logs on the band saw

#14

Re: cutting moderately -sized logs on the band saw

Jim Swank

>There's always a risk to both your body and the blade, no matter what you do. I prefer the electric chainsaw, as do most who have responded so far. If you must use the BS, there are a few things you can do to reduce the risk, even without making a full sled.

A piece of board nailed or screwed to the end of the log so that the flat edge rides on the table is one way. The board must project forward of the log so it can't be pulled into rolling forward during the cut.

The wedge already suggested will also work, but it must be large enough to prevent rolling.

The log must be of a size you can handle with reasonable comfort while keeping your fingers well away from the blade. Your body should be off to the side and your hands should never even be over the saw table.

I can buy several timberwolf blades for my share of one trip to the ER, and I have good insurance. I can buy an electric chainsaw for the price of 2-3 timberwolf blades. I can't buy new fingers at any price.

Re: cutting moderately -sized logs on the band saw

#15

Some need to re-read the post

Don Henthorn

>He is talking about cross cutting the log not ripping it. I say that because son

me who misread the post may have a better answer.

Re: cutting moderately -sized logs on the band saw

#16

Chainsaw for that size

Mike Nelson

>I'm with the rest here, an 8" especially wet log on 'my' band-saw has usually resulted in a broken or jambed blade. Last time I tried a big round wet log it broke the blade, blew open the door and threw the upper tire across the shop..exciting! I don't think twice about free-handing all sizes of wood with my saw but you have to be real careful with the round ones.

Re: cutting moderately -sized logs on the band saw

#17

Whoops, my mistake!!!!

Dominic Greco in Richboro PA

>I was reading some of the replies to this and noticed all the warnings and recommendations on using a chainsaw when it hit me. Did I misunderstand or misread the original question? I just re-read it and noticed that Eliot did say "cut to length". My sled and blade recommendation was meant for cutting a log length wise (rip cutting), along the pith. Not cutting cross cutting a log.

Cross cutting a log on a bandsaw is IMHO a recipe for disaster! It's too easy fr that blade to catch and BAM! That's not saying I haven't tried it. I did. ONCE!! It was NOT a pretty sight. After I changed my pants and threw away the mangled blade, I swore I'd never repeat that mistake again.

My suggestion, use a chainsaw (electric or otherwise). You'll be better off.

Sorry for the confusion.

See ya around,

Dominic

Re: cutting moderately -sized logs on the band saw

#18

Brad Vietje

Re: Whoops, my mistake!!!!

Brad Vietje

>Yup,

I'm with Dom. A small electric chainsaw is great for this sort of cutting chore. Since I got an electric saw, I haven't used a bandsaw for this sort of cut. For cross-cutting logs on the bandsaw, you could use a sled with a broad "V" -- even better if it had spikes to grip the log, like screw or nail points, to prevent any rolling motion.

Safe spinning,

Brad Vietje

Newbury, VT

Re: cutting moderately -sized logs on the band saw

#19

Re: Whoops, my mistake!!!!

eliot d

>Dominic, Thanks for your re-read. Before I read your amended message , I almost ordered the AS 3/8x3 TPI Timberwolf. Suffolk has a more expensive price for the alternate set (AS) blade ( which made no sense to me). Lenox, agreeing with me, couldn't understand that; and their price was $17.30 for a 150 inch blade compared to $25.79 for the Suffolk. So I was about to order it from Lenox when I re-read your post. Now I suppose it wouldn't hurt to have this blade anyway, but I haven't ordered from either place yet. I think I'll take the advice from most to use my chain saw for CUTTING TO LENGTH.

Getting back to BS blades, in general, are you sticking to the Suffolk alternate set 3/8 x 3 TPI Timberwolf? Is there any reason not to take advantage of a lower price from Lenox for what appears to be the same blade?