Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Power sanding question

Posts

Power sanding question

#1

Power sanding question

Jim Swank

>I've been using the wavy edged gold sanding discs (2" size) for some time now, and have been pretty well satisfied with the results. I've been using them on the Packard #125902 holder, along with a replaceable inner pad between disc and holder.

The holders last pretty well too, eventually failing by the foam separating from the plastic backer. I'm unlikely to change my sanding habits much at this point in time. Now I see Packard offering a "Pro" holder for a few more bucks.

Question #1 - Is the "Pro" holder likely to outlast the holder I've been using by enough to justify the price difference? Is there another holder that's likely to serve me better than either?

Question #2 - When it's time to buy more discs, is there another disc I'm likely to like even better than the gold wavy edge discs I've been using?

Re: Power sanding question

#2

Re: Power sanding question

Barry Irby

>I can't answer any of those questions, so I thought I would interject one you did not ask. I have torn the pad off one or two of my pads. I found the tear had a "topography" and the surfaces would mate almost perfectly. I coated one side with medium CA, stuck them together to coat both sides, pulled them appart and spritzed one side with accelerant and stuck them back together, holding them firmly for a moment. Been using them ever since. No apparent loss of function.

I would like to find about six soft pads with hexshafts with the snap feature and dedecate one to each grit. I do more damage to mine changing the paper than I do sanding. I woudl put the quick change connector in my drill and change pads rther than change grits on the pad. This would also let the pads cool between uses.

Re: Power sanding question

#3

Re: Power sanding question

TEK

>The sanding glove carries replacement hook material and also household "Goop" to glue it on with. I bought both from them at the Dessert Turning Roundup. They said if you buy "Goop" (there are several types) make sure you get the household type. It is clear and flexible and holds up to the heat of sanding. I've had good luck with both.

Re: Power sanding question

#4

Steven Antonucci

Barry- Make them!

steve antonucci

>I thought the same thing as you did- wouldn't it be nice to have one per grit, so I began thinking of "inexpensive" ways to achieve that objective.

I made my first prototype a couple of weeks ago and it works great.

Short list of parts:

1.) work arbor ($2) to fit your compressor sander

2.) small scrap of wood (I used maple)

3.) Some kind of hard foam (I used an old padded 5" sanding disk)

4.) hook and loop velcro

5.) Spray adhesive (Super 77/90)

Drill a hole in the maple and recess your screw head. Mount it on the work arbor, and turn it round and flat. Take the sanding disk and cut out a round (I used a holesaw). With a knife, carefully "fillet" the sanding material and the velcro off (it's the wrong side of hook and loop). Doesn't need to be perfect.

Spray one side of the foam and the wood disk with adhesive. Once tacky, glue them together. The face and the other diameter are likely out of round/flat, so mount on your lathe and turn them with a sharp spindle gouge.

My wife had the velcro from a craft store, and I only needed the hook side. Spray the backside and the other side of the foam, tack and press together. If you want, you can turn it round or just cut it with scissors.

I'd bet if you were doing this in an assembly line fashion, you could bang out a half dozen in an hour or so.

Steve

Re: Power sanding question

#5

Re: Power sanding question

Steve Worcester

>The "pro" holder is the same that I and several others sell. It is made by Tim Skilton in Australia. It is far more durable that the other, but more expensive as well. The Skilton pad is two types of foam glued together with a tee nut embedded in it and a washer and threaded hex shaft and nut to hold it all together. The velcro is replaceable, sort of. If too much foam is removed when you take off the old velcro, there isn't the full diameter left when you glue on the new velcro.

For what it's worth, use solvent based (not water based)contact cement if you want to glue the old pad back together. It will take the heat, and is more flexible than Goop (E6000) and superglue. Unless you like a more firm surface, then the other two will work fine.

Steve Worcester

www.turningwood.com

Re: Power sanding question

#6

Ric Taylor

Re: Power sanding question

Ric Taylor

>I've had the same experience. I keep reading comments from people who say their pads come apart and they have to keep buying replacements. I just can't understand those comments.

I've been using the same 2 inch pad for about six years. Once, about five years ago, the pad started to separate from the holder. I just slapped on some super glue, and it's been working fine ever since. It has been exposed to rough working conditions, many thinners while wet sanding, the sun, the heat, the cold of my unheated garage, etc. etc.

It takes a licking and just keeps going.

Similarly, I keep reading comments from people who throw away their sanding disk when the fabric peels off the back prematurely. When that happens to me, if the sanding disk is still good, a couple of drops of CA will glue the fabric back on the disk. I just make sure the CA is dry before I put the disk back on the pad, and I keep on sanding.

Ric

Re: Power sanding question

#7

Re: Power sanding question *LINK*

Darrell Feltmate

>Barry

I use an adaptation of the Roll-Loc system for just what you are saying. Take a look at my site under sanding.


Around the Woods - Sanding