Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Acrylic Pen Blank Help

Posts

Acrylic Pen Blank Help

#1

Acrylic Pen Blank Help

Pete (Stafford, VA)

>Good evening Ladies and Gents,

I'm having trouble drilling my acrylic pen blanks for the brass tubes. So far I'm 1 for 6; they are too expensive and too nice to waste at this rate!!!

The problem seems to be when the drill bit exits the reverse side, then bam - the blank explodes. I'm using Brad point bits, should I be using something else? Also, I'm running the drill press at about 1,200 - too fast or slow??

Thanks for any and all advice! Merry Christmas and Happy Holidays to everyone!!!

Pete

Re: Acrylic Pen Blank Help

#2

Re: Acrylic Pen Blank Help

eaglesc

>Brad point bits and dull ones are usually the reason for problems you mention.

I don't do many acrylics(thank God, plastic pens are a dime a dozen)

I suggest you slow down the DP, make sure you bits are CLEAN and sharp.

If necessary glue a waste block to the exit end of the bit.

Ask Santa for a Drill Dr., the model that makes split bits and convert the worthless overpriced brad points to split bits.

BTW a new bit out of the box is not necessarily sharp.

Re: Acrylic Pen Blank Help

#3

Re: Acrylic Pen Blank Help *LINK*

Brian

>Don't cut the blanks to the exact length - leave them 3/4" long and drill short of exit. Then cut them to length on the BS or Chop saw. See these instructions at Arizona Silhouette. Different pen perhaps but the beginning tells you how to avoid blowout. Also, don't take the budget route on drill bits - get the high end bits.


Arizona Silhouette

Re: Acrylic Pen Blank Help

#4

Ditto on drill bits...

Peter Teubel

>Last year, I replaced all my drill bits with top shelf bits. HUGE difference especially for metal and plastics. The two I use are Norseman and Triumph Twist. Not cheap, but worth every penny. They go thru material like "buddah", especially in the drill press. Links below:

http://norsemandrill.com/Mechanic_Facep19.html

http://www.triumphtwistdrill.com/products/jobber.asp (TriNado)

Re: Acrylic Pen Blank Help

#5

Re: Acrylic Pen Blank Help

Jim Shaver Oakville, Ont.

>Hi Pete,

I turn a fair amount of acrylic pens each year. I drill on my lathe, I use a Jacobs chuck and a Talon chuck with spigot jaws. I drill at 500rpm and take my time, usually drilling and retreating the drill every ��. I drill my way to depth then stop and trim the end on my band saw pen sled. I used to have the same problems with blanks blowing out. The heat build up inside the hole along with trapped shavings plugging the exit of chips, the sharpness of the drill and applied pressure are all factors to blow out. Keep it slow, keep it cool and know when to stop, forcing a bit through the end is similar to blow out in drilling a hole through wood, plywood comes to mind�but if it is supported it will be less likely as well. To achieve this I have in the past CA glued a scrap block from another cut off to the end of the pen blank, it works as well.

I turn about 350 pens a year now, about 85-100 are acrylic.

Take care,

Jim

Re: Acrylic Pen Blank Help

#6

Re: Acrylic Pen Blank Help

Pete (Stafford, VA)

>Thanks Guys - until I can go buy better bits I'll try cutting the blanks longer than needed and not drilling all the way thru.

Pete

Re: Acrylic Pen Blank Help

#7

Re: Acrylic Pen Blank Help

Denis L in Oshawa

>A few years back I was lucky enough to find a Bullet Point drill bit in 7mm, this has solved my problem of blowing out the hole at the bottom of the pen.This bit was made by Dewalt and asking them about such a tool brings a negative responce from them...

Re: Acrylic Pen Blank Help

#8

Re: Acrylic Pen Blank Help

eaglesc

>For what a few over priced bits costs like norseman etc a drill Dr makes HArbor freight bit work great.

I have been told I do fairly well with turning pens.

I woldn't waste any money on High dol;lar Bits.

I use the 115 piece set from HF that goes for around $40.00 on sale.

This was drilled with a "cheap" bit sharpened on the Drill Dr.

PLexiglass and copper.

It aint the cost of the bit it is how sharp it is.


img

Re: Acrylic Pen Blank Help

#9

Re: Acrylic Pen Blank Help

Russ Fairfield

>Pete, it isn't the name brand of the bit, it's how sharp it is, and that both cutting edges are identical. Some come that way from the factory, and they will cost more than those that you have to sharpen before you can use them. Either way, the drill bit will get dull and you will have to sharpen it or replace it.

It doesn't take very many ruined pen blanks to pay for the Drill Doctor or similar device. You have already spent $30 on ruined blanks.

Re: Acrylic Pen Blank Help

#10

Another Q - hijack

David Hammond, in Powder Springs GA

>I'm following this thread with much interest, because I just bought a brand new 12mm brad point bit from CSUSA and a Pink Coral True Stone jumbo pen blank. When I went to drill the blank on the lathe it split the blank terribly! I was so frusterated, but now my q: what about this Drill Dr.? Is there more than one brand or model, and which one do you guys recommend? And, is there a learning curve?

Thanks for the timely thread!

David

Re: Acrylic Pen Blank Help

#11

Re: Another Q - hijack

Pete (Stafford, VA)

>Thanks Dave - asking about the Drill Doctor was my next question!!

Pete

Re: Acrylic Pen Blank Help

#12

Re: Another Q - hijack

eaglesc

>The Drill Dr. has been around for a couple of years.When it comes to sharpening drill bits by "eye" have had bad luck. I know thewrre are many who say they can sharpen on a grinder but I am not one of them.

The Drill Dr. is a tool that has a diamond grit wheel, a chuck, and a refrencer to determine how far to place the bit in the chuck for sharpening.

It comes with a video but if you stay up late at nite you can see one of their informercials.

This is one case where I reccomend getting the top of the line model.The largest one will do bits up to 3/4 of an inch which is an important consideration if you are using it for bits for larger pens.

A nice feature of this tool is that it will make split point bits.

for me they drill more true than othe types of bits.

I ahve used a plit point from the Drill Dr. to drill a 3/8ths hole through 3/8th steel without a pilot hole using a Ryobi 18 volt cordless drill.

I may have a worthless Norseman bit laying around if anyone wants it.

I keep it to remind myself that just because a supplier says something is good and it costs an arm and a leg doesn't make it so.

The Drill Dr is everything the mfgr says it is.

DOn't take my word for it, Paul HArvey was also a spokesman for Drill Dr. at one time.

Re: Acrylic Pen Blank Help

#13

Re: Another Q - hijack

Wayne Kuhn

>The Drill Dr. is one of those tools that actually lives up to its advertisements. I have one of the original models. It works great.

If you get one, you will find yourself searching your shop for more bits to sharpen.

Re: Acrylic Pen Blank Help

#14

Re: Acrylic Pen Blank Help

John Vitosky

>The secret with acrylics is heat and cooling. put a ffew drops of water in to the blank when you have started drilling. The heat and friction cause the blank to explode and slow down.