Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Cherry spoons & scoops *LINK*

Posts

Cherry spoons & scoops *LINK*

#1

Cherry spoons & scoops *LINK*

Dominic Greco in Richboro PA

>Hi Everyone,

Here is a photo I just took of (4) spoons I turned/power carved, and (2) scoops. These are Christmas presents for my Mom and MIL. Although my wife has indicated that SHE would like a full set of these as well!

All are made from cherry I found along the side of the road, milled into flat stock, and allowed to dry for 2 years. The really nice part is that just about all these items were turned from scrap wood that was cut from the flat stock. I knew I was right when I didn't discard those pieces!

The spoons all measure about 12" long and have varying sized heads. The scoops are about 5" to 5 1/2" long and are just under 3" in diameter.

Before turning the scoops, I finally broke down and purchased a copy of Richard Raffan's "Turning Projects". It was well worth it! His method for turning scoops was the easiest I've seen so far. I was able to turn a scoop in half the time I did before.

The bowl section of the spoons were power carved with a rotary rasp purchased from PSI's showroom in Phila PA. I was lucky they had any left. Since this was a discontinued item, I think I got the last pack they had. With the spoon clamped firmly to the top of my workbench I chucked this bit into my trim router and used it to hog out the material. Before I started I sketched out the perimeter of the bowl to be a guideline. I'll say this about rotary rasps, they sure can hog away material FAST!

When I was first researching how to turn spoons, I used the link provided to me when I was looking for information on scoops. It lead me to Woodturning Online. What a fantastic resource that site turned out to be! I have Bill Turpin to thank for that link. (Thanks Bill!) One gent on that site suggested using ball end mills to hog out the material. I purchased one from ENCO and made the mistake of getting a double fluted version. It takes too fine of a bite and clogs up WAY to easy. I should have gotten a single fluted version. Oh well, better luck next time! Luckily PSI had these rotary rasps on hand.

The finish is Mineral Oil followed by buffing and a liberal coat of bee's wax.

See ya around,

Dominic


img

Woodturning Online

Re: Cherry spoons & scoops *LINK*

#2

Re: Cherry spoons & scoops

Lan Brady

>Dom,

Found wood is so satisfying when you end up with project this nice.

Great job !

Lan

Re: Cherry spoons & scoops *LINK*

#3

Re: Cherry spoons & scoops

Mike Rubes, Apex, NC

>Hi Dom,

Those are AWESOME! I really like them a lot! Not only is it a great save for the wood, but the final product is really top notch. Honestly, it is a mystery to my how you do one of the spoons. I see how you can turn the handle between centers, but I am fuzzy about the bowl part of the spoon. I would love to see a picture or two of in progress works and/or a description of the steps you take to do them. I know several cooks around me that would love something like this for their kitchens!

Thanks for the post, really nice work. The extra steps of embellishing the shafts and handles really pays off as well. Makes the pieces look that much nicer.

I hope all is well in PA.

Mike

So many fun things to try in Apex, NC!!!

Re: Cherry spoons & scoops *LINK*

#4

Re: D'ouh!!!!

Mike Rubes, Apex, NC

>Hi Dom,

I completely missed that you had a link to the wood turning page in your post! Must have been too early in the morning. That page gives some great in progress photos and descriptions :)

Thanks for the link. I really love your spoons and want to try this myself very soon.

Take care,

Mike

Going to make a spoon in Apex, NC!

Re: Cherry spoons & scoops *LINK*

#5

Re: Cherry spoons & scoops

Jim Shaver Oakville, Ont.

>Hey Dom,

You have been busy Buddy!!

These all look great...

Take care,

Jim

Re: Cherry spoons & scoops *LINK*

#6

Re: Cherry spoons & scoops *LINK*

georgetroy

>Thanks for showing Dominic. You did a good job on these. You just happen to catch me wanting to do some spoons. I appreciate your links to turning spoons on the lathe. Another source for woodcarved spoons and some are turned is Pinewood forge. They have knives, photos and links for making spoons. I made some flat kitchen type spoons years ago when I was doing the Renaissance Festivals. I still have my orginal pieces to make more. GT


http://www.pinewoodforge.com/

Re: Cherry spoons & scoops *LINK*

#7

Re: Cherry spoons & scoops

Ron in Drums PA

>Great looking spoons $ scoops

After looking at these, I feel I should try my hand at turning some.

Re: Cherry spoons & scoops *LINK*

#8

Re: Cherry spoons & scoops

Jennifer@Indy.USA

>Nice Job Dom! These are going to make great gifts!

Jen

Re: Cherry spoons & scoops *LINK*

#9

Thanks everyone

Dominic Greco in Richboro PA

>Thanks for all the compliments. If I can get some free time this weekend, I may be able to turn some for my wife. And maybe even some spatulas ala Richard Raffan.

It's funny. I never would have thought I would enjoy making utilitarian stuff so much! But it's pretty cool once you get the hang of it.

See ya around,

Dominic