Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Epoxy Problems

Posts

Epoxy Problems

#1

Epoxy Problems

Paul Coppinger

>About 2 weeks ago, I mixed some 30 minute, clear epoxy purchased at the local hardware store and filled a 1" diam hole that was about 1/2" deep. The weather was very cold for East Texas (low 30s)and to-date, the epoxy is still sticky on the top. I mixed 50-50 like instructed. I have had the piece under a light bulb for almost 2 weeks now and still it is not hard. Should I give up and dig it out, should I coat some hardner over the top or is there some other way to complete the hardening process like hotter lamp, etc.

Thanks for your help,

PAC

Re: Epoxy Problems

#2

Re: Epoxy Problems

Peter Hyde

>Hi Paul,

All epoxies are not equal and I would suspect the cold initial setting temperature was way to low so the thermal reaction never happened. Also a hole this size would need some sort of filler mixed into the epoxy. Epoxy is meant to be a thin coating as the setting properties will be greatly accelerated when left in a big glob which can cause excessive heat and even ignition.

So I think it would be prudent to dig out the soft epoxy and clean the hole with acetone. Then in a warm environment around 70*F mix some fresh and add a filler such as sanding dust until it is the thickness of heavy cream.

Use white vinegar to clean up tools and brushes before the epoxy sets. Wash thoroughly with dish soap and warm water and dry thoroughly. Do not allow vinegar to contaminate your epoxy supply.

Peter

Visit my site at:

http://www.oldtoolsshop.com/Galoots/pHyde/

By the way you can clean up tools and brushes with white vinegar but never allow vinegar to corrupt your good epoxy so wash everything in dish soap and warm water and dry thoroughly.

Peter

Visit my site at:

http://www.oldtoolsshop.com/Galoots/pHyde/

Re: Epoxy Problems

#3

Keith Tompkins

Re: Epoxy Problems

Keith Tompkins

>Perhaps try West Systems epoxy...not clear, but will harden like a rock. Expensive, however.

Re: Epoxy Problems

#4

Re: Epoxy Problems

Paul Coppinger

>I didn't mention that I was trying to cover a seashell recessed into the hole and therefore wanted the clear epoxy so it would be visible. Can I heat it more to continue the reaction? If I dig it out and start over, what will make a clear filler for the hole to let the shell show?

Thanks,

PAC

Re: Epoxy Problems

#5

Re: Epoxy Problems

jwoodwright

>I would use the 2-part accrylic they sell in Craft Store, like Michael's... It's meant to embed objects and such.

Watch the Temp. Too Cold and you don't get the Chemical Reaction.

The Heat everyone is mentioning is from this Chemical Reaction, External Heat won't help...

This is the same stuff the Penturners are using to make blanks... So, you can sand and buff and polish this material, when it has set.

Re: Epoxy Problems

#6

Re: Epoxy Problems

john lucas

>paul you will have to dig out the uncured stuff. It won't ever harden. To refill I use one of 3 things. clear Inlace, System 3 mirror coat fro m woodcraft, or cast-in-craft from the local hobby shop. I like the Cast-n-craft the best for filling voids in flat surfaces. The Inlace is excellent for filling voids in vertical or curves surfaces because you can let if harden a little until it's like toothpaste, however it may not fill every gap if you do this. It's better to build a dam and pour the stuff in when it's thin.

The system 3 mirror coat is a beautifully clear coat but it can get so viscous when it's cureing that it will actually run throuhg the pores of the wood. It's great if you have really punky wood and want to harden that area. You might need several applications.

Re: Epoxy Problems

#7

Re: Epoxy Problems

Robin Corell

>You've gotten some good comments and advise so far but I wanted to add one common source for epoxy failing to set. Unlike polyester which can be kicked with an additional coat of properly mixed resin, epoxy that is not mixed properly will never set. a source of unmixed resin is the sides and bottom of the container as well as the mixing implement. It is common to want to use every last drop of an expensive material by scraping every last bit even more than when you scraped the sides when mixing. A remedy for this is to pour the resin into a clean container (don't forget to scrape the sides really well) and then use a clean mixing impliment (aka a stick). Mix it a bit more then feel free to use every little bit you can coax out of the container without fear of it not being mixed properly.

Of the many diferent resins, epoxies, and rtv rubbers Ive used, as long as the temp dosent fall below freezing as soon as the temp is brought above 70 it will resume the curing process. I used to use this property to my advantage in hot weather by storing my resin in a refrigerator I had for that specific reason so I could gain a few extra minutes working time. This works with bondo too.

as for your project it is time to dig it out. If part of it is hard then just clean it off really well and fill it back up with the same material. It is is soft all the way through it is likely it was either not mixed properly or the producct has expired. Either way I would recomend doing a small sample befor refilling your turning with the same product.

Robin Corell

Re: Epoxy Problems

#8

Re: Epoxy Problems

Paul Coppinger

>Thanks to all those who responded to my question. I think the low temp caused my problem. I bit the bullet after lunch today and started digging. Brushing acetone softened the top of the epoxy helping the digging. When it was all evaporated, the loose stuff could be blown away. Then repeat, about 1000 times. In about 30 minutes, I had it all dug out. Now I have to decide to just leave it open around my sea shell or try the cast-n-craft stuff John mentioned.

Thanks again,

PAC