Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Decorative Walnut Bowl

Posts

Decorative Walnut Bowl

#1

Decorative Walnut Bowl

Mike Brazeau

>The inspiration for this piece came from a combination of things. In my workshop, I had been looking for a while at a beautiful piece of black walnut that was about 2� thick and about 13� x 20� that I had won off our GHWG raffle table some time ago. It had talked to me long enough. Second was a recent visit to Derek Andrews� site at http://www.sunrisewoodcrafts.ns.ca/ I liked Derek�s Bits�n�Bobs bowl. These bowls are smaller than this piece and intended as a catchall for keys or change etc. In an early morning Eureka moment, I completed a sketch and headed for the lathe. My initial attempt for the approximately 3� wide edge didn�t appear too pleasing. I wanted to use my homemade Triple point tool and incorporate some beading as well as some texturing. I had the outer edge too thick, so it was back to the lathe to let the wood talk to me some more. I was able to play lots of games with the Sorby Texturing Tool as the edge was progressively thinned down. Due to some warping of the original piece, the final thickness is about 1 5/8� and it is 12 �� in diameter. It was sanded starting with 120 and going to 400. I finished it with one coat of homebrew Danish Oil followed by a couple more of Watco Clear Danish Oil. I wiped it down with some old denin so I could avoid little bits of paper in the texturing. The bowl was immediately claimed by my wife and now sits on our entry hall table, not as a catchall, but as a decorative accent piece or as we term them in our house, a Foo-Foo. My sister, who is always very kind, referred to it as an objet d'art. I'll take it!

Mike


img

Re: Decorative Walnut Bowl

#2

Texture/Beading Detail

Mike Brazeau

>The combination photo shows a top on view of the random dot pattern generated and attempts to show the lace chain like pattern that is achieved with the repetition of each spoke on the texturing cutter.

As I experimented I tried various approaches with the Sorby Texturing tool. The spiraling wheels didn�t give me the effect I want, so I went back to the texturing wheel that resembles the rear sprocket on a bike. The beads were cut first with the Triple point tool and touched up later. The walnut was very hard to emboss especially in an area of an embedded limb that is about 20% of the circumference and much denser than the rest of the wood. I discovered that by pushing the tool very firmly into the wood and doing a pull cut that took about 15 seconds to cover 3/8 to � an inch, gave me a beautiful random pattern. It was important that I had the tool rest portion, which is integral to the Texturing/Spiraling version of this tool, so that I could keep a steady pull and the tool oriented vertically to the work. I did a repeat application as I thought needed at the time. If applied too long, you end up with the characteristic orange peel effect. The key is to experiment. As I progressed, I used Clapham�s Sanding and Cutting lubricant (love that stuff) to highlight the wood and give me an idea of what the final finish would be when finished with Danish Oil.


img

Re: Decorative Walnut Bowl

#3

Reverse of walnut bowl

Mike Brazeau

>Through good luck rather than good planning (leave that for the next one!) I was able to reverse on my 8� Oneway Vacuum chuck on the inner most bead pair and finish off the bottom with some more beading with the trusty triple point tool.


img

Re: Decorative Walnut Bowl

#4

Brad Vietje

Very Nice -- Beautiful !

Brad Vietje

>

Re: Decorative Walnut Bowl

#5

Re: Very Nice -- Beautiful !

Norm Smith in Nova Scotia

>Mike, I like what you did with this piece. Very nice.

Norm

Re: Decorative Walnut Bowl

#6

Re: Truly an object d'art!

Allen Neighbors

>

Re: Decorative Walnut Bowl

#7

Steven Antonucci

I would have liked it better if the bowl...

steve antonucci

>form on the top was more prominent? It's a great turning and the finish looks awesome, but I get the feeling that I would have wanted the bowl to be larger with a little bit less bead and texture work. It may be the angle that you took the picture, but it looks like it's flat on the bottom and curved on the top. I would have switched the contours.

Just my $.02.

Steve

Re: Decorative Walnut Bowl

#8

Re: Texture/Beading Detail

Jennifer@Indy.USA

>Mike,

I really love this design. The texture and the beads work so well together. Great job! A beauty for certain.

Jen

Re: Decorative Walnut Bowl

#9

Re: Decorative Walnut Bowl

Jim Shaver Oakville, Ont.

>Hi Mike,

I really like it, The details and proportions are all very pleasing to look at, well Done!

Take care,

Jim