Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

How many use a foot switch for turning?

Posts

How many use a foot switch for turning?

#1

How many use a foot switch for turning?

Ryan Dicker in Renfrew, Ontario

>I was just wondering the other day how many people use a foot activated switch to control the power to their lathe. I have been using one since I started turning, (about 3 years) and find that I stop the work to look at what I am actually doing to the wood more often. Generally this helps learning cutting techniques by comparing the quality of the cut.

From a safety standpoint, I feel much more in control of the lathe by not having to reach for the switch should something happen.

I wouldn't want to be without one...

Ryan

Re: How many use a foot switch for turning?

#2

Re: How many use a foot switch for turning?

Russ Babbitt

>I couldn't use one. I move around too much. I do have a remote switch on a magnet I can place anywhere on the lathe I want. Some suggest a fixed switch at the headstock and one at the tailstock end so your "memory" always knows where it is. So in an emergency, a reflex action can find it.

Re: How many use a foot switch for turning?

#3

Re: How many use a foot switch for turning?

Allen Neighbors

>I don't use a footswitch, because I'm on both sides of the lathe, many times, on nearly every piece. I have a remote switch (magnetic) for my Old Griz, but don't have one for my Oneway. Wish I did.

Re: How many use a foot switch for turning?

#4

Leo Van Der Loo

Re: How many use a foot switch for turning?

Leo Van Der Loo

>Hi Ryan

Ryan I always use a foot switch, only I normally have it not on the floor unless I do hollow turning where I can have the turning tool in the turning, holding on and able to turn on or off the lathe with my foot, any other time the switch is right on the ways where I am, either end or frond or back side of my lathe, I don't have to go and find it, it's right there under my hand.

Have fun and take care

Leo Van Der Loo

Re: How many use a foot switch for turning?

#5

Re: How many use a foot switch for turning?

Mike Brazeau

>I tried one a few years ago on my old Delta Rockwell. Once I upgraded to the Oneway with remote, I put it away. The way I turn now, I don't think I would use it.

Mike

Re: How many use a foot switch for turning?

#6

Re: How many use a foot switch for turning?

Ed in Leaside (Toronto, Ontario)

>I have both the on/off & deadman foot switches from LV. I didn't like the on/off on the lathe as when I wanted to stop in a hurry more often than not my foot couldn't find the switch. That one got moved over to the bandsaw and I used the deadman for about 6 years on a stretched Mastercraft lathe. Kind of a necessity when you're turning 7' away from the switch.

Re: How many use a foot switch for turning?

#7

Re: How many use a foot switch for turning?

Russ Fairfield

>I am of the school that says that graceful forms come from the graceful tool control that comes from graceful body movement. We can't do the "dance" with our foot planted on a switch.

My advice is to forget the foot-switch, and learn to move around more. Your woodturning will improve because of it.

Re: How many use a foot switch for turning?

#8

Re: How many use a foot switch for turning?

Ryan Dicker in Renfrew, Ontario

>What you say is likely true Russ. Often the foot switch causes me to stretch out one leg and pivot around it to make the pull cuts around the outside tops of bowls. I do however find it useful for spindle turning, as I am stopping the lathe often enough to warrant using it. I am more likely to slide the switch to where I am working on a spindle turning than on a bowl.

I'll have to try that out....now only if I could find the thing under all these shavings....

Re: How many use a foot switch for turning?

#9

Re: How many use a foot switch for turning? *LINK*

Darrell Feltmate

>Ryan

about the only time I use a foot switch is for hollowing forms. I have not made a captured hollowing rig and so do it by hand. As such, there is not much movement around the lathe and a foot switch is handy as I have to start and stop quite often to clear the chips from the inside. It was well worth the time to make it.


Around the Woods

Re: How many use a foot switch for turning?

#10

I can dance, I can dance all night...

Robin Corell

>When I bought my delta 1460 from an Oregon state surplus auction it came equiped with a foot switch. When it was delivered I was under the gun to deliver some patterns so I just pluged it in and used it. I really didn't want the foot switch and figured I could scrap it out later when I wired in a pull-up-to-start switch on the top of the wood base directly above where the back end of the motor is. I had turned on a lathe of the same model with a switch like this and had liked it very much. No accidental starts and easy to hit to turn off quickly. The switch is actually a standard single pole switch on tho motor with a long metal rod that has a ring on the top end and a slot on the bottom where it attaches to the switch with a kotter key.

Ive seen the same set up on a couple of old delta bandsaws but I have no idea if it is a stock thing on their lathes.

The foot switch that my lathe came with is one of those industrial units with an orange steel cover that is big enough to acomodate my size 13 work boots. The switch is wired in with heavy extension cord type wire and can be positioned anywhere around the lathe. It is the type of switch that you step on to start and step on agasin to stop. It took some getting used to and I did occasinaly swear in its general direction but now I find it convienient and no longer have plans to change it out.

I don't quite understand how dancing and a foot switch are exclusive. I must be doing it wrong or its the music I listen to. (Taj Mahal at the moment)

Robin Corell