Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Turning Hollow Form Vessels...Long.

Posts

Turning Hollow Form Vessels...Long.

#1

Turning Hollow Form Vessels...Long.

Wally Dickerman in Arizona

>Way back in the 70's (was that before some of you kids were born? in Fine Woodworking magazine there were a couple of articles about David Ellsworth, with lots of photos of the amazing hollow form vessels that he was turning. At that time, no one else was doing anything close to that. I looked at those pics and decided that I wanted to turn something like that. It was several years later that I made a boring bar hollowing tool and got started. That was over 20 years ago. Since then I've scarcely turned anything else.

I teach classes in beginning hollow forms and I have a how-to handout for the students. I occurred to me that for those of you who are just getting started in hollow forms, that some of the tips from that handout might prove helpful. (Icould have used some help when I was getting started)

Set the tool rest height so that the cutter on your hollowing tool is cutting on the centerline, or better yet, a little above center. Cutting below center invites a catch.

Use your hollowing tool with the cutter tipped down slightly. This will give sort of a shearing cut. This is especially true when using a rounded scraper on your tool.

Never allow the tool to touch the rim when cutting. A sure way to break the vessel if a catch occurs.

If you plan to apply decorative beads or grooves, or other turned adornments, do it before final hollowing of the roughed-out inside. The vessel will distort a little as you turn the walls thin.

If you use a glue block on an end-grain piece, you'll get a stronger glue joint if you cut a small tenon on the blank. Cut a matching opening in the glue block. I don't recommend using a glue block on deep end-grain pieces.

A vessel often warps a little as you turn the walls thin. To avoid problems later, you should complete all turning and sanding of the area around the rim before proceeding on to final hollowing.

Do final hollowing a section at a time, working your way down so that you're always cutting against thicker wood.

Measure wall thickness frequently. That's especially true when you're deep inside the vessel. Calipers, such as double ended calipers are a must.

Some turners completely turn and finish hollow vessels while the wood is still wet, and that's okay. I prefer to allow the rough turned vessel to dry. When adding a collar or other rim treatment I don't want any later distortion of the wood as it dries.

For deeper pieces, a steadyrest is really a necessity. One can be shop-built, using plywood and in-line skate wheels.

There is, of course a lot more to hollow form turning, but these some of the basics. The ultimate success of a vessel is determined by it's form.

Wally

Re: Turning Hollow Form Vessels...Long.

#2

Re: Turning Hollow Form Vessels...Long.

Barbara Gill, Remlik VA

>This is getting printed and put into my collection in the shop. Thanks Wally.

Re: Turning Hollow Form Vessels...Long.

#3

Re: Turning Hollow Form Vessels...Long.

DKWalser

>Wally,

Thank you for taking the time to do this. Do you have your handouts available in electronic form? If so, maybe we could post them on the Arizona Woodturner's web page (assuming you are willing). If your handouts are not in electronic form, I'd be glad to type them up for you.

Re: Turning Hollow Form Vessels...Long.

#4

Re: Turning Hollow Form Vessels...Long.

John Lucas

>Thanks Wally. I don't turn a lot of hollow vessels,especially big ones, and need to be reminded of the basics often.

Re: Turning Hollow Form Vessels...Long.

#5

JL

Re: Many thanks, from a non-hollowform turner

JL

>

Re: Turning Hollow Form Vessels...Long.

#6

Re: Turning Hollow Form Vessels...Long.

George Van

>Thanks Wally. Is there a "rule of thumb" for the length of vessel you would start using a steady rest?

Re: Turning Hollow Form Vessels...Long.

#7

Re: Turning Hollow Form Vessels...Long.

Allen Neighbors

>Thanks, Wally, this is good information. I've saved it to my laptop, and will print it out for the notebook in the shop.

Basics are good. We all need 'em. :o)

Thanks again.

Re: Turning Hollow Form Vessels...Long.

#8

Re: Turning Hollow Form Vessels...Long.

Wally Dickerman in Arizona

>I'll see if I can send it to you.

Wally

Re: Turning Hollow Form Vessels...Long.

#9

Re: Turning Hollow Form Vessels...Long.

Wally Dickerman in Arizona

>No rule of thumb. Depends on how secure the piece is fastened to the lathe and how firm the wood is. Your tool will tell you if the cut could be better. Actually, just about any piece 5 inches or longer would benefit from the use of a steadyrest.

Wally

Re: Turning Hollow Form Vessels...Long.

#10

Thanks Wally....

GaryG in MD

>...this is the kind of thing that makes WC so useful. We all appreciate it, particularly from one of the masters like you. ...Gary

Re: Turning Hollow Form Vessels...Long.

#11

Re: Turning Hollow Form Vessels...Long.

Ron McKinley

>I've been itching to try a hollow-form for a long time. Thanks for the info. I think I'll get going on one........Ron

Re: Turning Hollow Form Vessels...Long.

#12

Re: Turning Hollow Form Vessels...Long.

George Van

>Thanks Wally, I had better find the time to make one after looking at the ones I have roughed.

Re: Turning Hollow Form Vessels...Long.

#13

I would dearly like a complete copy

jared

>I am anticipating that my wife is buying me a don pencil hollow turning set for Christmas, at least that is what I asked her for. I have never turned a hollow form before and the words of an obvious master would sure be nice to have. If a copy becomes available please let me know. {I will not copy them and sell them or anything like that}. Thanks Jared

Re: Turning Hollow Form Vessels...Long.

#14

Re: Turning Hollow Form Vessels...Long.

Don O.

>Thanks a ton Wally, outstanding information. I just got a new Don Pencil hollowing setup (Thanks B.G.!) that I am itching to try. These pointers will help a lot. Can't beat great tips from a true master!