Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Conductor's baton

Posts

Conductor's baton

#1

Conductor's baton

John Meikrantz

>Any advice on turning a conductor's baton? My son would like to make one for his band teacher. I have read a little on the topic, but have never tried turning anything long and thin on the lathe. What is the basic shaft diameter at base and tip?

Thanks,

John

Re: Conductor's baton

#2

Re: Conductor's baton

john lucas

>I made the one I gave my son's conductor. The shaft was 1/4" and tapered to around 1/8". It' about 10" long. I did it by sliding the 1/4" square piece through the headstock and holding it in my chuck so that about 2" extended. I turned this and then extended another couple of inches. To keep the whipping down I took the point out of my live center and adjusted the tailstock so the tip of the shaft just stuck in the hole without touching anything.

Most conductors are pretty picky about length of the rod and the weight and shape of the ball end so my son snuck a look and measured all the critical components.

I made the shaft from cherry and the body from purple heart. I've also made one from Holly and walnut.

Re: Conductor's baton

#3

Turn the handle, fiberglass rod for shaft *LINK*

Bill Turpin in WNC mountains

>My grandson turned several batons for his band teacher last year. We used 1/8" and 3/16" white fiberglass rod from McMaster. Part #8543K27 and 8543K28 for 2 bucks and change for five feet pieces. Cut them over long and director can have you cut them to length. Tip can be shaped with any fine grinder in seconds. Shipping will cost more than the material. The stuff cuts easily on a band or chop saw. It also can be cut on the corner edge of a grinding wheel.

White FG is much more visible for the musicians. Also if the band director is a baton tapper on the music stand, a turned shaft will not last very long. Directors can get almost violent beating the baton on the stand to get musicians attention. This also eliminates the difficult task of turning a needle. Grind a few notches in the end of the shaft so that the five minute epoxy has something to bite into, in the hole in the handle. With the ease of only turning the handles you can make several with different woods and handle shapes.

My grandson gave them to his band director just before their Christmas concert. His director was in tears when she showed them to the whole audience. The smile on that twelve year old's face was worth a million dollars. :)

Bill in WNC mountains


McMaster

Re: Conductor's baton

#4

Re: Conductor's baton

David Breth

>You'll probably get a great response and genuine appreciation for the gift, but just a heads up - a baton is a very personal thing to many conductors. They choose them carefully, collectiing a handful over many years, they carry them in sturdy protective containers. They are interested in balance, weight, visibility, feel in the hand, length, etc. The gift, while I am certain will be very much appreciated, may not see a great deal of use in the long run.

By the way, for finish, I'd recommend going in the middle relative to gloss. Ultra-glossy can be a distraction to an audience as lights pick it up, but it does need to draw the attention of the group being conducted.

But you never know - could "turn" out to be the favorite one ever.

Whatever my two cents are worth, you've probably got change coming...

David B.

Re: Conductor's baton

#5

Great idea Bill.

John Lucas

>

Re: Conductor's baton

#6

I don't get credit

Bill Turpin in WNC mountains

>I got this idea from that other WW site, the wet one a year ago.

Bill

Re: Conductor's baton

#7

Re: Conductor's baton

John Meikrantz

>Thanks, everyone for your help and input. I've got some good ideas now of how to get this accomplished.

John

Re: Conductor's baton

#8

Re: Turn the handle, fiberglass rod for shaft

John Meikrantz

>Bill,

Turned a prototype today out of a scrap curly anigre pen blank that I had laying around. As it turns out (no pun intended) I live relatively close to the McMaster Chicago distribution center, so I ordered some fiberglass and picked it up at Will Call, no shipping was required. I can't begin to imagine all of the cool stuff that I can pick up there, now that you put the idea in my head.

The hardest part was getting the blank mounted squarely and securely in the chuck (used a Nova Precision Midi chuck with 25mm jaws). Any tips on mounting a small blank for spigot turning? Also tried to cut the 1/8" fiberglass rod with a hacksaw, which made a mess of the end, of course. Then took it to a disc sander to clean up. Fine touch needed to prevent overly aggressive stock removal!

Thanks again for everyones input. No, I didn't take any pictures yet.

John

Re: Conductor's baton

#9

Re: Turn the handle, fiberglass rod for shaft

Bill Turpin in WNC mountains

>Put the blank in your chuck with tail end center marked. Use a live center in the tailstock. Turn the blank to round and start to taper the tail end. I use a Jacob's chuck in tailstock to hold a matching drill bit for rod hole. Put the live center back in (insert tip into hole) and use to support the baton handle to complete the turning, apply finish and part off from the chuck. Thinking back I believe I actually used the square edge/corner of a cheap HF bench grinder to cut the rod. Dremel wheels should also work. Have fun

Bill in WNC mountains