Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

DELTA 64-715

Posts

DELTA 64-715

#1

DELTA 64-715

Mike from Tn.

>Hey guy's. For the money is the Delta worth it? Any idea why the price dropped $400 to $600 over the last two yrs.? Price now is at about $550. Has anyone had one of these for more than two years? If so would you buy another one? Thanks.

Re: DELTA 64-715

#2

Re: DELTA 64-715

Russ Fairfield

>Personal opinion. The price dropped because it was overpriced and they weren't selling them. The price is now down to where it should be for this lathe.

Re: DELTA 64-715

#3

Re: DELTA 64-715

joaz

>I had one. Light duty. Bearing's are cheap. Don't expect to do anything heav-duty. Good for spindle work. Maybe small bowls.

just my 2cts.

Re: DELTA 64-715

#4

Re: DELTA 64-715

Norm Smith in Nova Scotia

>I agree with Russ. Todays Delta products are now comparable to Craftsman.

norm

Re: DELTA 64-715

#5

JL

Re: DELTA 64-715

JL

>I have a 46-715. It is now in "storage". The bearings are cheap. The Reeves drive has a bit too much vibration. I plan on doing a cleaning and recondition on it and eventually use it for buffing. I have a Jet 1642 EVS as my lathe now. If I had to buy it over, I'd have gone for the Jet in the first place and saved the money on the Delta to buy something else.

Re: DELTA 64-715

#6

Re: DELTA 46-715

Jack Savona

>It was basically my first lathe and I turned many bowls, pens, wine stoppers, and spindle items on it. It certainly works, but I found the quality lacking (adjustment handles snapped, reeves drives were noisy at best, cracked at worst, tool rest extension broke TWICE...). I rate it as a capable, NOISY, poor-quality lathe. To be fair, Delta did send parts, but it was annoying not to have a good, quiet lathe.

The motor was fine, the bed strong (with ballast), the tailstock grip weak, the parts poor quality.... If I had it to do over, I would have gone with a Jet. With my inexperience, I didn't know the name 'Jet', so I went with the "brand" name Delta. Mistake.

Re: DELTA 64-715

#7

Re: DELTA 64-715

Jim Rutten

>Don't go there, Mike. I had one for a couple of years. I am an occassional turner (because of my work not my desire) and heard all the horror stories. Mine worked fine for a while and then, I don't know if it was the bearings or the Reeves drive, it started woobling like crazy on bowls over about five inches. I didn't have Jacks good luck with support and got a hateful person on the line. I will not have another delta product in my shop. If you are only going to do spindle turning it might be fine, but in my opinion it would be better to save some more money and get a Jet, Powermatic, or something like that. Good luck whatever you decide!

Re: DELTA 64-715

#8

Re: DELTA 64-715

Wilford Bickel

>Redmonds in Atlanta is selling the 46-715 refurbished for $299 right now. Apparently they got a lot of them in as the sale has been going on for a couple of months.

Re: DELTA 64-715

#9

Re: DELTA 46-715

Brodie Brickey

>I had a delta 46-715 and also had the noise and bearing problems. There were also issues lining up the tailstock and headstock after outboard turning. Not worth your time.

Go with Jet, Powermatic or Nova. The old Nova 3000 had a 16" swing and belts for adjustment. It sold for $900 new, you might be able to find someone getting rid of theirs as they move up. I've heard they're pretty good.

Brodie