Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Extending a Lathe

Posts

Extending a Lathe

#1

Extending a Lathe

Tomm

>I need to turn two back chair posts (legs and chair backs =42 inches) that are six inches longer than my Jet 1236 can handle. Do you think it is possible to make a temporary extention using hardware store parts for the jet lathe? Thanks for your thoughts.

Re: Extending a Lathe

#2

Re: Extending a Lathe

john lucas

>Absolutely. I've done it with 2x4's. For small spindles you don't need a huge amount of rigidity. The more the better, but you can get buy with less than perfect if you don't mind taking your time. Just build it as rigid as you can.

I've also backed a mini lathe up to my big lathe, raised the mini until the tailstock was the same height as the big lathe and clamped them togehter with a coupld of boards. The I used the mini lathe tailstock with the big lathe headstock.

Re: Extending a Lathe

#3

Re: Extending a Lathe

Russ Babbitt

>Another option is to make the posts in two pieces.

Re: Extending a Lathe

#4

Re: Extending a Lathe

Bob Fawcett

>I recently did this with some bedposts. Turn a tenon on one piece, and bore a corresponding hole in the next piece.

This worked fine for my posts and turned out to be a major plus. When I first thought I was finished I assembled the 3 pieces I had turned for a post and decided the posts were too short. No problem, I just turned another piece and extended the post.

Re: Extending a Lathe

#5

Re: Extending a Lathe

Wilford Bickel

>I've not tried it but I read an article where a shelf type system was made to mount on the wall and hold the tailstock. The lathe was then just moved away from the wall whatever distance was needed to handle the piece - seemed like a good stable way to extend the length you can handle. I would think you could use one of the laser levels to make sure you get everything lined up.

Re: Extending a Lathe

#6

Steven Antonucci

Laser idea... (if you really need to do this...)

steve antonucci

>Why not get a small laser pointer and mount it in a chuck? It would project a straight line to "infinity" and you could built your tailstock support to the exact right size and alignment?

If I was going to attemt this (no reason to try except for the challenge of doing it...:-), I'd built an extension out of MDF that could be bolted or clamped to the ways. My Nova even has the registration holes to do it. For alignments sake, the extension would have a tongue on it to fit the ways and add extra support.

If it was going to be something that I made to be disposable, I'd A-frame the legs or use some other cabinet with "shimming" to match heights. I bet I could get another 3' or so out of my lathe doing this!

Too much time on my hands.

Steve

Re: Extending a Lathe

#7

Re: Extending a Lathe *LINK*

Bill Grumbine (Kutztown PA)

>Tom, I did something along these lines back in 1999, but it was a larger scale. I turned the mast for my sailboat between two lathes. Steve has an interesting idea, but the fact of the matter is, the further away your two centers are, the less important alignment becomes. I had the centers 14 feet apart, and just sort of eyeballed the thing by sighting down the empty tapers of the mini lathe. Everything came out fine. I used the same system to re-turn some fire damaged spindles for a friend of mine who does restoration work.

Good luck with it.


If you are interested in reading about the process I used, it is still up on my personal site. The link is below.

Bill


Turning a sailboat mast

Re: Extending a Lathe

#8

JL

Re: Thanks for sharing...

JL

>now I know how to turn some long bedposts without making them two sections.

Re: Extending a Lathe

#9

Re: Thank You

Tomm

>Thanks for your ideas.