Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Sanding

Posts

Sanding

#1

Sanding

robo hippy

>I have been chatting with Vince (VincesWoodNWonders) who has the wonderful blue sanding film discs, and have been left with a real head scratcher. What are the optimum speeds for sanding? There is lathe speed, disc speed, and pressure to consider. Somewhere there has to be an ideal combination that will yield fastest removal and smoothing without heat build up which of course leads to glazing of the disc and wood, heat cracks, hook and loop pad (and some times glue) failure, and burning the woods. What is too fast? What is too slow?

I have both the slow and high speed Sioux/Milwaukee angle drills. At first I liked the high speed ones. Now I like the slow speed ones. I have found that the slow speed model gets the job done just as fast as the high speed one, and is easier on the wood, pads and discs. When I had to use the high speed one while my slow one was down, I put a piece of cork under the trigger to keep the speed down. Vince told me that he recomends a disc speed in the 700 rpm speed (slow speed drill is 1 to 1,200 rpm) on the coarser grits and slower than that on the finer grits.

I like to turn green to final thickness, let them dry and warp, and then sand and finish. For lathe speed, ususlly I am in the 100rpm or less. I usually keep the trigger all the way down if for no other reason because this is the easiest speed to maintain. I have found that the firm pads are much faster to use than the soft pads, and the firm pads from Vince that have rounded over edges (I would guess 1/4 inch radius minimum) work very well on the inside of the bowl. I have, at least for the time being, been sanding up to 180 or so with the firm pad and then switching to the soft pads for the higher grits, 220 and up.

I also dry sand. I have seen some who wet sand with oil. Does this make much difference other than the dust factor?

robo hippy

Re: Sanding

#2

Re: Sanding

John Lucas

>I sand with the wood traveling slower than the disc. I don't run the disc at full speed using a Dewalt electric drill. I don't know what I run the lathe speed at but it's pretty slow, well under 500. Sometimes on natural edge I will run the speed up when power sanding the wings but in the last year or so I've been sanding natural edge with the lathe off.

I just started using Vince's blue discs and like them except for saning up close to a foot. My other discs just fit pads with a slight wrap around and would get quite close to the "crease" between a foot and bowl. Vince's discs don't do that as well.

Re: Sanding

#3

Re: Sanding

Bill Hale / Woodspinner

>I do most of my power sanding with the lathe on and use a sanding block. I run the lathe at about 700. The primary consideration, in my mind, is heat. You can get the wood hot, even at this speed, if you press to hard.

Light pressure, med speed and fresh sandpaper. Do not try to get the very last out of the paper. Pretend someone else is buying you the sandpaper.

Good turning and be safe

Bill in Casa Grande, AZ.

Re: Sanding

#4

Dick Hines

Re: Sanding

Dick Hines

>A good way to judge how fast it to fast is hold your hand on the piece while it is turning. If it gets "HOT" you are going to fast.

Re: Sanding

#5

ebd

Re: Sanding

ebd

>Re. wet sanding. IMHO it depends on the wood somewhat but I find that it tends to muddy the sharpness of the grain/figure. This seems especially true in wood like black walnut. I also find that in segmented pieces you can get color bleed darker into lighter wood.

Re: Sanding

#6

Re: Sanding *LINK*

Vincent Welch

>Hi Reed,

I seen your post so I thought I would mention what we talked about. I am not an expert but I have had many conversations with some experts and some very knowledgable hobbist. Plus I have my own findings that I beleive are relevent. One of the biggest mistake is sanding to fast and not allowing the abrasive to do its job which is cut wood. The disc will start skidding across the wood surface burnishing your wood and ruining your disc. SLow everything down. If you start at 120 grit at 500-700 RPM great. Take your time with the lower grits 120,150,180 If you have a lathe that allows you to change rotation that can help esp. with stubborn end wood grain. One of the biggest suggestions that I can make is this. As you progress through the grits lower your sanding speed! So when you get up to 320-400 you do not need much if any speed to sand. Random Orbital Sanding is best at this point if you have a ROS. Think about it the grit is so fine that you really need to allow the disc a chance to cut the surface. Also be sure to wipe off your project or blow off your project with compressed air in between sanding grits. Again esp. as you progress through the higher grits. Once you get through the lower grits and you are samding with 320 and above it should only take a few passes before you wipe/blow off the surface and continue on to the next grit. If you are finding scrathes with higher grits you need to go back and start again with a lower grit. Also make sure your discs are clean and fresh. I am writing a page on my website called "Sanding Suggestions" that will offer this information and tips from professional turners. It is in the works now.

John,

I just got in NONradius firm innerface pads. My 3 3/8 dics come to the edge of these pads with NO overhang for when you need to get up to those edges. ALso, check out my new Scuff Bright Pads.

Hope this helps,

Vince


http://vincesWoodNWonders.com