Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

flute down cutting

Posts

flute down cutting

#1

flute down cutting

john lucas

>There is an article in American Woodturner by Phil Brennion on making a turned salt box. In the article he shows a flute down cut. This has confused many people. I hope these photos show the cut. It is a very safe cut for cleaning up endgrain. It is a bevel rubbing cut, not a shear scrape. give it a try. The start of the cut can be a little tricky but once it gets started and the bevel is rubbing it's very controllable.


img

Re: flute down cutting

#2

Re: flute down cutting

Leppikallio

>Looks pretty effective. Like skew with long point up...?

Re: flute down cutting

#3

skew cutting

john lucas

>You are correct. Cutting endgrain with the long piont up is really tricky. You better be good with the skew before you try this.

I prefer to cut with the long point down. I usually start with the tip above center and arc in like using a parting tool. You have to rub the bevel of course.

If you want a really clean cut, necessary when turning things like spalted maple end grain, cut from below the center line with the handle really high. This is a very easy cut and if you use light pressure will leave even very nasty wood slick as a baby's butt. Don't know how slick that is, I'll have to ask Micheal Jackson. Oooh that's bad.

Re: flute down cutting

#4

Re: flute down cutting

Carole Valentine

>I use that flute down cut all the time. Never having had anyone to show me what I should or shouldn't do, I have tried all sorts of stuff and in the process discovered many things that work and quite a few that I should have had better sense than to try! LOL Most of the disasters were with the skew, BTW.

Re: flute down cutting

#5

Re: skew cutting

George Van

>"If you want a really clean cut, necessary when turning things like spalted maple end grain, cut from below the center line with the handle really high. This is a very easy cut and if you use light pressure will leave even very nasty wood slick as a baby's butt."

John, am I correct that you are still describing the skew cut with the long point down? Thought I would be sure before I give it a try. Thanks.

Re: flute down cutting

#6

Re: skew cutting

John Lucas

>George Here's the photo. for some reason I couldn't download these from my home computer.


img

Re: flute down cutting

#7

ignorance is bliss

John Lucas

>I look back at some of my early pieces and wonder how in the world I did them with the skills I had. I think I didn't know that I couldn't do it so I did it anyway. does that make sense? Actually you hit on a very good point that I try to teach. That is, I take every tool and try to see how many different ways I can use it. A good example would be the parting tool. I use it like a mini skew to turn beads, shallow coves and sometimes to finish off the bottoms in a skew like cut. Oh yea I do use it like a parting tool also.

Re: flute down cutting

#8

Re: skew cutting

George Van

>Thanks for taking the time John!

Re: flute down cutting

#9

Re: skew cutting

John Lucas

>George it was either take a photo or write a 500 word essay and hey guess what, I'm a photographer so you know what I chose.

Re: flute down cutting

#10

Brad Vietje

Re: flute down cutting

Brad Vietje

>I use this a lot. Unlike the skew (handle high and long point down) I use the bowl gouge with handle as low as possible, and tip up. This is also a great way to make very smooth catch-free cuts with the traditional straight-across English grind on a deep bowl gouge.

I also learned from Robert Chapman about using a bowl gouge in this fashion on the inside of shalllow bowls, and especially plates and platters. For end grain pieces that are shallow enough you can make a fantastic cut from the center outward toward the edge -- nearly impossible to get a catch except when starting the cut from the outer edge in.

As John says, try it -- you'll like it !

Safe spinning,

Brad Vietje

Newbury, VT

Re: flute down cutting

#11

Re: ignorance is bliss

Barry Turner

>Ain't it amazing what you can do........until you start learning and realize you don't have the skills. Maybe ignorance is bliss. :-)

Re: flute down cutting

#12

Re: ignorance is bliss

Mac

>Ignorance has ALWAYS worked for me........

Re: flute down cutting

#13

which direction is the wood spinning?

keith zimmerman, Normal, IL

>