Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Wiring -- a bit OT

Posts

Wiring -- a bit OT

#1

Wiring -- a bit OT

eliot d

>My lathe and band saw are both 220. There's no more room on the circuit panel, but there is a 220 outlet dedicated to the clothes dryer about 20 feet away. What I do when I want to run either the lathe or the BS is to remove the dryer plug and plug in the lathe or the BS. So there are two approximately 25 foot long heavy duty "extension power cords" that I have wired to the BS and to the lathe. These long cords run along the floor wall edge and are held there with numerous

U -fasteners. Something tells me that this arrangement is not up to code. It works perfectly well, and I don't want to spend a fortune rewiring the whole shop, but should I? Would putting the long extension cords in conduit be an improvement? Why would it?

Re: Wiring -- a bit OT

#2

Re: Wiring -- a bit OT

gil jones

>Conduit would be a fine way to protect the extension cord (the flexible, blue type would be easy to route). 25-feet is not far enough to be a problem as long as the wire size is capable of handling the amperage your machines are demanding. Home depot sells 10-gauge extension cord in bulk (it is yellow, and you install your own plugs). 3-wire is OK as long as no 120-volt circuits are internally tapped off inside the 220-volt machine circuit (such as a light). If that is the case, you will need a 4th wire to use as a dedicated ground to protect yourself from the 120 volt circuit in case it were to electrify the metal parts of the machine.

Re: Wiring -- a bit OT

#3

ReYou will find a nice selection......

Jamie Donaldson

>....of heavy duty cords at an RV supply dealer.

Re: Wiring -- a bit OT

#4

Re: Wiring -- a bit OT

Stuart Johnson

>You might look into the possibility of using the existing dryer connection to run a sub panel. This would give you the ability to run circuits with the appropriate sized breakers for your machines.

Re: Wiring -- a bit OT

#5

Actually…

Rod Peterson -- Ormond Beach

>> 3-wire is OK as long as no 120-volt circuits are internally tapped off inside the 220-volt machine circuit (such as a light). If that is the case, you will need a 4th wire to use as a dedicated ground to protect yourself from the 120 volt circuit in case it were to electrify the metal parts of the machine.

Just to pick a nit, when you need the fourth wire, it's for a neutral. The third wire is already in use as a dedicated ground.

Rod

Re: Wiring -- a bit OT

#6

Re: Wiring -- a bit OT

Joe Flemig

>I did this at my house. I have a gas dryer, so I cut the box out of the laundry room and punched through the wall to the garage on the other side. There, I installed a 30 amp subpanel where I run most of the garage lights a 220v circuit for the lathe/table saw/etc., and a 115v 20A circuit for other power tools.

Joe Fleming - San Diego

Re: Wiring -- a bit OT

#7

Re: Actually�

gil jones

>Thanks Rod, you are correct. I had a case of Age-Activated Attention deficit Disorder when I typed ground instead of neutral.

Gil

Re: Wiring -- a bit OT

#8

Re: Wiring -- a bit OT

Fog Tanner

>Like you, I had the problem of a limited space in my service panel and needing to add additional circuits to my model airplane workshop and pool. I only had one 220 space available and needed two. I used a quad breaker which gave me two 220 volt circuits. One fed the pool and the other fed the service panel in the workshop. The quad occupies the same space as a normal single 220, but has the two outer breakers tied together and the two inner are tied together (at least on mine). In your case one side would feed your drier and the the other you lathe/bandsaw.

I later did away with the pool and added a garage/workshop/studio (depending on the price of the piece). Initially I just ran wire from the quad breaker. But, recently my wife and daughter bought a larger glass kiln and I had to run 100 amp (was 50A)service to the GWS (dothpotp) which meant adding a subpanel off the main service panel and pulling larger wire. I had to replace the quad with a 100amp which runs to the sub panel. The sub panel now feeds the two out buildings (each with their own service panels). My lathe, bandsaw, comprssor and the kiln are all 220 in dedicated circuits, so I don't have to unplug anything.

Re: Wiring -- a bit OT

#9

Re: Wiring -- a bit OT

Barry Irby

>I don't see any reason you couldn't run a single circuit with multiple outlets on it and just plug in the various tools. You might have to remember not to run more than one tool at a time, but then if you are working alone, that is not a problem. OTOH, if you did run two at a time, you might trip the breaker. If the breaker is "handy" as in nearby, it is not a problem to reset it after turning off the tools. As long as the smallest wire in the circuit is rated to handle the output of the breaker, this would not be dangerous. I lived here for a while, thinking I was going to move and "borrowed" the dryer circuit for my TS. They seldom ran at the same time, but once or twice I forgot to restart the dryer and I was encouraged to get a half size or mini breaker to allow for both the dryer and TS. A good sound thrashing with moldy laundry makes a mini breaker seem quite reasonable.