Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Turning Knitting Needles

Posts

Turning Knitting Needles

#1

Turning Knitting Needles

ScottIn Annapolis

>I am trying to turn knitting needles. As you know, thin shaft, lots of flex. I figure I need a steady rest and I am looking to you all for ideas. This is some small diameter turning - similar to wine goblet stems and the steady rest needs to acomodate small shaft diameters.

I have a Sears lathe very similar to the Delta and Jet Mid-sized lathes with standard rails and tool slot dimensions.

Thanks

Scott

Re: Turning Knitting Needles

#2

Re: Turning Knitting Needles

Stuart Johnson

>Can you feed it through the headstock? Someone posted about holding a small, long blank with a four jaw chuck. You leave a few inches sticking out, turn and finish then feed out a couple more inches. Repeating until it is as long as required. You can not touch a finished sections again.

Re: Turning Knitting Needles

#3

Re: Turning Knitting Needles

Dennis Daudelin

>The thing that has turned me off (so far) on trying to turn knitting needles is that they are precisely measured. There is a scale that is used to size them. So, in turning them, you'd have to pick a size and then ensure that they are correctly turned...

Any thoughts on this??

Dennis

Re: Turning Knitting Needles

#4

Brad Vietje

Re: Turning Knitting Needles

Brad Vietje

>That's what stopped me, too ! I have started thinking of those wooden sticks (like hairpins) used to hold women's hair because they don't have to be exactly width x or length y... Can also be combined with a decorated piece of leather or similar, with two perforations for the wooden stick to pass through.

Safe spinning,

Brad Vietje

Newbury, VT

Re: Turning Knitting Needles

#5

String Steady? *LINK*

Devon Palmer

>With something that thin....

A spindle steady might be overkill. Maybe a coupla these guys to stabilize, although it may add to much time if you're doing these as a production item. I've actually turned a small cup wiht a #2 morse taper at the end, placed it in the tailstock with 4 nails, and strung up the end of a short trembleur that way (never could get one to survive the bedan tho LOL)

- Devo


String Steady Plans

Re: Turning Knitting Needles

#6

Re: Turning Knitting Needles *LINK*

MountainMan

>Try this link - I think there may be another - gotta find it in my favorites!!

http://www.turnedtreasures.com/index.html


http://www.turnedtreasures.com/index.html

Re: Turning Knitting Needles

#7

Re: Turning Knitting Needles

MountainMan

>Here is the other I was thinking of - my wife has purchased several of his hooks - they are really beautiful!!

http://www.turn-of-the-century.com/tchome.htm

Regards

TheM MountainMan

Re: Turning Knitting Needles

#8

Re: Turning Knitting Needles

Bob Fawcett

>A Beall collet chuck might be good also. Use a small dowel that will fit through the headstock as a blank. They usually have nice straight grain to start with as well. Go to the Box and pick through all the dowels in the bin.

Re: Turning Knitting Needles

#9

Re: Turning Knitting Needles

ScottIn Annapolis

>Unfortuantely, the DC-motor on the headstock does not allow passing the needle through the headstock - this is also a problem for me in that I cannot use a vacumb chuck on this lathe either.

Re: Turning Knitting Needles

#10

Re: Turning Knitting Needles

ScottIn Annapolis

>Yeah, I have a size chart and if I can get them stiff for turning then I can match the required sizes.