Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

So I've got this new Jet 1236...

Posts

So I've got this new Jet 1236...

#1

So I've got this new Jet 1236...

David Breth

>and I'm enjoying it, BUT, I need to make use of the stand to put a tool area beneath the lathe, and maybe weigh it down a bit, or at least leave myself some room to add weight in the future.

I've had a bit of a time finding photos of other 1236's, or other lathes for that matter, where people have added a shelf/box, whatever, beneath the lathe. Could I trouble some of you to post photos of your clever arrangements?

Thanks very much!

David B.

Re: So I've got this new Jet 1236...

#2

JL

Re: So I've got this new Jet 1236...

JL

>Check Dominic's article on the 1642 EVS in the articles section. I adapted his ballast box and put a drawer unit on it. You could make a similar ballast box and suspend it from the sides of your base and then put a drawer unit or something similar. Just a thought.

Re: So I've got this new Jet 1236...

#3

Pix

Mark Mandell - Gone Round In Jersey

>Here's a couple:


img

Re: So I've got this new Jet 1236...

#4

Re: Pix-2 

Mark Mandell - Gone Round In Jersey

>


img

Re: So I've got this new Jet 1236...

#5

Re: Pix-3 

Mark Mandell - Gone Round In Jersey

>


img

Re: So I've got this new Jet 1236...

#6

Another thing I'd recommend...

GaryG in MD

>David,

As you have probably found by now, the 'off' switch is not very accessible or easy to use and is hence not a quick enough or safe way to turn off the lathe in a 'difficult' situation (like when something starts flapping). The worst part of it is that you have to reach across the danger zone to get to it. Not good. I would recommend that you add an external in-line switch (like a switched power strip) and mount it with rare-earth magnets so you can move it around depending on your needs for each particular piece. I have done so, and it makes me feel a lot safer. ...Gary

Re: So I've got this new Jet 1236...

#7

Re: Pix-2

bob davis

>that tool rack is really cool

Re: So I've got this new Jet 1236...

#8

The swing away tool holder is SO friggin kewl!

Devon Palmer

>

Re: So I've got this new Jet 1236...

#9

Brad Vietje

Re: Pix-2

Brad Vietje

>Wow, that swing-away tool rack is a great design. The rolling base would drive me up a wall sideways, as I'd be tripping over it every second. I wonder if that could be adapted to allow little feets under the lathe ? Maybe a angled stretcher under each end connecting the "front" leg casters to the back of the unit?

I strengthened the thin metal leg stretchers on mine with a 2 x 4 frame for a little more "umph" and added 8 cinder blocks, and placed a piece of plywood for a tool shelf atop the concrete blocks, but under the bed. I did a lot of green wood bowl turning, so the weight of all those concrete blocks came in handy -- maybe that's why I had to replace stuff so often on mine ?

Safe spinning,

Brad Vietje

Newbury, VT

Re: So I've got this new Jet 1236...

#10

Re: More detail?

Mike Hamilton

>Hi Mark,

Do you have a closer shot of the pivot points for that tool rack? I'd appreciate details on how much of your setup is tool storage versus space for ballast. I have a 1236 demanding improvements (since the wallet is too empty for the excellent 1642 deals going on now).

Regards,

Mike Hamilton

Plainfield, IN

Re: So I've got this new Jet 1236...

#11

Re: So I've got this new Jet 1236...

Ed Larson

>David

This is setup that I made for my 1236. I had to raise the lathe about 8 inches ( I'm 6-5) so I put used 2 X 6's for a top and then added more blocks on top to raise the bed level. I used 2 X 6's for the bottom shelve and added two drawers. The tool rack swings in and folds against the lathe bed. There are 4 X 4's on the bottom to raise the lathe and give it more stability. The tool rack is too close and interfears with long tools so I would extend the top another 8-10 inches past the bed and move the tool rack. The drawers are great (I store sandpaper, chucks, drives, etc) but they do attrack shavings. The setup is very stable.

Ed


img

Re: So I've got this new Jet 1236...

#12

Response to All

Mark Mandell - Gone Round In Jersey

>Sold the lathe; rack went with it so no more close-ups, but . . .

The tool rack swung from two points. The top "point" was a 5/16" bolt (with washers) that was set into the cross brace that picked up both of the top leg-set bolts for stability. The pivoting frame rode on a nylon washer and was secured with a cap nut.

The bottom pivot was just that; a 1/4" bolt and nut through a short piece of angle iron bolted to the bottom bolt on the one leg bracket point.

The angle iron was 7/8" stuff I had lying around. The top brace was cut and welded next to the pivot and then again at the rack to run the full length of the tool rack for rigidity. If I had tied it to a single point, the whole thing would have tended to rotate down and away. The long brace attached at a single point at the far end of the rack to keep it from sagging.

VERY IMPORTANT was to also incorporate a rotation stop on the top pivot point frame to prevent the rack from swinging into the spinning wood. Mine kept the rack a minimum of 12" behind the bed so it was never less than 6" from a workpiece, but always easy to get to and would swing out of the way if I was working with a long handle sticking out behind the lathe.

The rack was super convenient for that lathe because all the tools I needed for a piece could be loaded and held at arm's reach.

I found I didn't have a problem with the mobile base frame. You could, of course, do one of those "I" frames, but I had didn't feel the need to go there. The box carried 3 bag's worth of sand [230lbs]; the concrete blocks were optional.

Hope this helps.

Re: So I've got this new Jet 1236...

#13

Re: So I've got this new Jet 1236...

David Breth

>Thanks very much for all the responses. I really appreciate it. I'm leaning more toward a setup like Ed's, primarily because it is a setup I'm capable of doing without assistance, though I'm hoping to shield the "stuff" a bit from shavings. I'll have to put some thought to it. My hope is to pretty much store everything there - chucks, tools, sandpaper, ear/eye/face protection, crying towels, swear jar, bandaids....

Mark - your setup was pretty incredible. I'm sure I'd gore myself with it, but it is pretty incredible. I'm thinking it took you about five minutes to sell the lathe with that feature attached to it.

And Ed - I just saw your post about the smoked motor. Sorry to hear that. Hope you can recover without breaking the bank. I've already sent psychokinetic vibes to my machine begging it not to follow suit. Those conditions can be contagious.

David B.

Re: So I've got this new Jet 1236...

#14

Bravo!

Ron McKinley

>Now that is really innovative! Bravo! ......Ron

Re: So I've got this new Jet 1236...

#15

Re: Necessity Is A Mutha

Mark Mandell - Gone Round In Jersey

>As inventions go, anyway.

In my Shoe Box Woodshop that also holds a cabinet saw, 18" bandsaw, router table, jointer, chopsaw station, P'Max 22-44, drill press, mortiser, ossilating sander, lathe, DC system, water heater, water treatment, and two furnaces all in about 15x25, just about everything (other than the water and heat stuff) has to be movable. The tool rack moving with the lathe allowed me to store the whole deal in as compact a space as possible.

That's why I pretty much "had" to go with a Stubby when I decided to upgrade. It actually takes up less shop space than the JET did. It does not, however, move, and I do miss my very handy rack.

|;-}}

Re: So I've got this new Jet 1236...

#16

Re: Another thing I'd recommend...

Ed Larson

>Gary

Thanks for the idea about the switch and the use of magnets. Now that I have some time while waiting for the new motor I will installl the second switch.

Ed

Re: So I've got this new Jet 1236...

#17

Re: Saw all I needed to see to copy.

Al Crandall (N.E. of Indy)

>Mike, we'll get together soon after a club meeting or whenever our schedules mesh and I can help you build this. I've copied a lot more complicated things than this. Mark will understand.

Re: So I've got this new Jet 1236...

#18

Re: Saw all I needed to see to copy.

Mark Mandell - Gone Round In Jersey

>Ain't no thang.

Re: So I've got this new Jet 1236...

#19

Re: Thanks Al

Mike Hamilton

>