Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

3520B Motor w/ Thermal Overload??

Posts

3520B Motor w/ Thermal Overload??

#1

Andy DiPietro

3520B Motor w/ Thermal Overload??

Andy DiPietro

>I was running my Powermatic 3520B lathe at full speed on the slow belt setting for about 1 1/2 hours on Monday night. I was Beall buffing a half dozen HF's for my club meeting the next night when the motor would not restart after changing buffing wheels. The drive controller was still on. It displayed rpm's when I rotated the spindle with the hand wheel. I blew out a little dust from the motor fan and from the inside of the bearing housing, but nothing worked. So I figured that it was either the main switch or the remote had dirty contacts. So Tuesday night when I came home from work I tried the lathe and it turned on like nothing was wrong. So I shut it off and cleaned a small amount of dust in the sealed remote switch. But that was not the problem. So now I am thinking that maybe the controller has a built in thermal overload? But I do not know why it would overheat in a cool basement shop. I saw a similar posting by John Lucas. Does anyone have any insight to this problem??

Re: 3520B Motor w/ Thermal Overload??

#2

Re: 3520B Motor w/ Thermal Overload??

Hooligan

>The inverter on the 3520B, and now the 4224, is a bit goofy, from what I have read. It seems as though it acts as a GFCI and detects minute differences in Milliamps, but seems to correct itself.

I don't know what, or why, nor does tech support.

Re: 3520B Motor w/ Thermal Overload??

#3

Andy DiPietro

Re: 3520B Motor w/ Thermal Overload??

Andy DiPietro

>Inverter Gremlins Huh! There is a small knob on the controller and it is set to Min. Is there a setting that I should be using! Do you have the Tech support #? I did not get an inverter manual with the Lathe.

Thanks

P.S. Each time I see your name posted I think of that Crotch Walnut HF you sold. Awesome job on that.

Re: 3520B Motor w/ Thermal Overload??

#4

Dick Hines

Re: 3520B Motor w/ Thermal Overload??

Dick Hines

>Try unpluging the power cord and let set for a couple of minuets. Then plug it back in. The inverter may just need reseting.

Re: 3520B Motor w/ Thermal Overload??

#5

Re: 3520B Motor w/ Thermal Overload??

john lucas

>Unplugging is the only thing I can guess. I've run my 2035A for a whole day once and no problem. If it happens again I would call the tech reps and see if you can get an answer.

Re: 3520B Motor w/ Thermal Overload??

#6

Re: 3520B Motor w/ Thermal Overload??

john lucas

>I have one other thing. You don't have the remote switch do you. There have been some problems with the remote switch not letting the lathe start. It's in the switch itself so if it continues unhook the remote and go back to the way it was. The main switch seems to work perfectly. At least I haven't heard of any problems.

Re: 3520B Motor w/ Thermal Overload??

#7

Re: 3520B Motor w/ Thermal Overload??

Hooligan

>Thanks!

The number for Tech Support should be 800-274-6846.

As far as the inverter goes, don't mess with any of those settings, as it could be mucking up the drive.

Give the gents at TECH a hard time, and see what they tell you.

Re: 3520B Motor w/ Thermal Overload??

#8

Andy DiPietro

Re: 3520B Motor w/ Thermal Overload??

Andy DiPietro

>Yes I do have the remote switch and it has been hooked up since day one. I would have been better the next day if the lathe did not start because I was ready to check the remote with a multi-meter. Then if it was the remote switch I could have easily jumpered it out.

The first thing I tried was shutting off the 20 amp breaker for 5 minutes, but that did not help. I will call tech support tomorrow and push them for an answer. I did not mess with the inverter settings. If it happens again I will jumper the remote switch and see what happens.

Thanks as always.

Re: 3520B Motor w/ Thermal Overload??

#9

Re: 3520B Motor w/ Thermal Overload??

Chuck Engstrom

>I downloaded the manual for the 3520A controller a while back and will be glad to send it along as an attachment if anyone wants it. It's 234 pages, 4.1 MB, mainly, I think, because it covers several models for various power levels. I suspect the 3520B uses the same item, as does a friend's Jet 1640/220v.

I doubt that it would shed any light on the present issue but it will impress you with what a complex gadget it is.

Best--

Chuck Engstrom

Re: 3520B Motor w/ Thermal Overload??

#10

Brad Vietje

Re: 3520B Motor w/ Thermal Overload??

Brad Vietje

>I was told not to mess with the inverter settings on mine. The two buttons on there that may help are the "reset" and "run" buttons. It may have helped to push the reset, followed by the run button after it failed to start. I had to do this once when I caused a big catch by doing something stoooopid (not a great idea to turn around with a 5/8 bowl gouge inside a big bowl), and the motor instantly shut off. After a few moments of thinking I had ruined something, I pushed reset and run, and all's been well since then.

Safe spinning (don't drive like my brother),

Brad Vietje

Newbury, VT

Re: 3520B Motor w/ Thermal Overload??

#11

Bypass the remote switch first

Jerry Hall

>The first thing you should do is bypass the remote switch. It's a very good chance that is it. They are somewhat famous for failing.

See Powermatic 3520 Tips, Reviews, Sources, Links

http://www.woodturner.org/vbforum/showthread.php?t=1839 and go to message 6 for simple bypass instructions.

If it is there is a chance you can talk PM into sending you a free replacement. Or buy a better switch!

Re: 3520B Motor w/ Thermal Overload??

#12

Andy DiPietro

Re: Response from Tech Support

Andy DiPietro

>I talked with Tech support this morning and they think it is one of two things.

1. As we have all stated it could be a problem with the remote switch. He said if I find out that the switch is bad then he would send me a new one at no charge.

2. One of the wires connected to the Inverter may be loose do to vibration and/or moving the head stock around alot. So I will check this tonight.

So thanks for everyones input.

I rather be turning!!

Re: 3520B Motor w/ Thermal Overload??

#13

Andy DiPietro

Re: Problem solved it was the Remote Switch

Andy DiPietro

>After running the lathe this morning for a couple of hours it decided not to restart again. So I jumpered the switch and it started up. I checked all the wire terminals in the Inverter and they were all tight. There was very little dust in the Inverter. So it was definetly the switch. I have to wait till Monday to get Tech support to send me a new switch.

Thanks everyone.